Also assume that all heat rejection processes are to a low

Assignment Help Mechanical Engineering
Reference no: EM13638559

A gas turbine power plant operates under the Brayton cycle, which is non-ideal due to heat losses from the compressor and turbine. The cycle uses air as the working fluid, has a pressure ratio of 12:1 and a mass flow rate of 100 kg/s. The cycle has a net power output of 50,000 kW and a thermal efficiency of 38%.

Air at 300 K and 100 kPa enters the compressor, which has an unknown isentropic efficiency and losses heat at the rate of 1000 kW. The turbine has an isentropic efficiency of 86.1% and a heat loss rate of 1000 kW. If the turbine were isentropic, the working fluid would leave at 963.3 K. Hint: When working with the isentropic efficiency definition, use the exact form of the definition with the ratio of works/powers.

Assume that the heat transferred into the system originates from a high temperature reservoir whose temperature is equal to the maximum temperature of the cycle. Also assume that all heat rejection processes are to a low temperature reservoir with a temperature of 300 K. Using the properties of air at 300 K, find:
The peak temperature of the cycle.

Reference no: EM13638559

Questions Cloud

Two identical point charges of q 125 x 10-8 c are : two identical point charges of q 1.25 x 10-8 c are separated by a distance of 0.90 m. what is the minimum amount of
On a smoggy day in a certain city the ozone concentration : on a smoggy day in a certain city the ozone concentration was0.50 ppm by volume. calculate the partial pressure of
Calculate the mass concentration in microgm3 of a : calculate the mass concentration in microgm3 of a mono-dispersed aerosol with dp 10.0 micron rhop 2.1 g cm-3 and n
The electric potential at the center of a square is -3 v : the electric potential at the center of a square is -3 v when a charge of -q is located at one of the squares corners.
Also assume that all heat rejection processes are to a low : a gas turbine power plant operates under the brayton cycle which is non-ideal due to heat losses from the compressor
A proton of mass mp 167 x 10-27 kg and charge e 160 x : a proton of mass mp 1.67 x 10-27 kg and charge e 1.60 x 10-19 c is accelerated from rest through an electric
Two wheels of mass m and moment of inertia i are connected : two wheels of mass m and moment of inertia i are connected by a massless axle of length l. the system rests on a
Determine the mass flow rate of hot water withdrawn from : the hot water needs of a household are met by a 60 l electric water heater whose heaters are rated at 1.6 kw. the hot
An analytical laboratory balance typically measures mass : an analytical laboratory balance typically measures mass to the nearest 0.1 mg. what energy change would accompany the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd