Air standard diesel cycle has a compression ratio

Assignment Help Mechanical Engineering
Reference no: EM13703049

An air standard Diesel cycle has a compression ratio of 15, and the heat transferred to the working fluid per cycle is 800 Btu/lbm. At the beginning of the compression process the pressure is 14.7 lb/in^2 and the temperature is 60 F. Determine:

a) The pressure and temperature at each point in the cycle.

b) The thermal efficiency

c) The mean effective pressure

Reference no: EM13703049

Questions Cloud

Air from a workspace enters the air conditioner : Air from a workspace enters the air conditioner unit at 30C dry bulb and 20C wet bulb. The air leaves the air conditioner and returns to the space at 20C dry bulb and 6.5C dew point temperature. If there is any, the condensate leaves the air conditio..
Determine the density of refrigerant : Determine the density of Refrigerant-12 at 3MPA and 200 degrees celcius by using the principle of corresponding states.
Determine net radioactive heat transfer from each surface : A cylindrical furnace is 0.4 m long and 0.4 m in diameter. The two ends are maintained at 600 K and 700 K with emissivities of 0.6 and 0.7 respectively. The lateral surface has an emissivity of 0.8 and a temperature of 800 K. Determine the net radioa..
Minimum wall thickness of pole after incorporating factor : Erected a new sign welcoming people to the campus. The sign is painted on a rectangle of graphite reinforced epoxy which will not bend and measures 3 ft high and 5 ft wide. This sign is fastened along its 3 ft side to a hollow 2014-T6 aluminium (allo..
Air standard diesel cycle has a compression ratio : An air standard Diesel cycle has a compression ratio of 15, and the heat transferred to the working fluid per cycle is 800 Btu/lbm. At the beginning of the compression process the pressure is 14.7 lb/in^2 and the temperature is 60 F. Determine the pr..
Determine the rate of energy transfer from the air to water : Water enters one stream of an unmixed stream heat exchanger at 20°C and increases in temperature by 10°C. Air enters the second stream on the heat exchanger at 400°C and 5 kg/s. The air temperature at the exit of the heat exchanger is 200°C cooler th..
Determine the shear and moment diagrams : Consider a simply supported beam of length 50ft subjected to a uniformly distributed downward load of 10kips/ft from x=10ft to x=40ft and concentrated downward loads of 100kips at x=10ft and x=40ft.
Average tractive effort exerted by the locomotive : An electric locomotive together with its train has a mass of 200 tonne. The average tractive resistance to motion is 55 N/tonne while starting from rest up a gradient of 1 in 100. Calculate time taken to travel the first 1 km if the average tractive ..
Determine if the entropy change of the system is positive : Consider two ideal gases, A and B that are initially separated. For each of the following processes, the gases are allowed to mix. Determine if the entropy change of the system is positive, negative, or zero. Explain. (a) The process occurs isotherma..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd