Air is contained in a vertical cylinder fitted with a

Assignment Help Mechanical Engineering
Reference no: EM13624770

Air is contained in a vertical cylinder fitted with a frictionless piston and a set of stops as shown in the sketch (distance between the piston and the stops is 0.6 m and distance between the stops and the bottom of the cylinder is also 0.6 m). The cross-sectional area of the piston is 0.05 m^2. The air is initially at 400 C and 0.2 MPa. The air is then cooled by heat flow to the surroundings.

A) Determine the temperature (C) of the air inside when the piston reaches the stops.

B) Determine the final pressure (MPa) if the cooling is continued until the temperature reaches 20 C.

Reference no: EM13624770

Questions Cloud

A survey of 144 retail stores revealed that the average : a survey of 144 retail stores revealed that the average price of a microwave was 375 with a standard error of 20 if 95
A refrigeration cycle is a reversed heat engine which of : a refrigeration cycle is a reversed heat engine. which of the following has the maximum value of the co-efficient of
Air enters a constant-diameter tube with an average : air enters a constant-diameter tube with an average velocity of 2 ms at a temperature of 400 k and a pressure of 0.12
Two objects are orbiting each other under the influence of : two objects are orbiting each other under the influence of the force of the gravitation force between them. object 1
Air is contained in a vertical cylinder fitted with a : air is contained in a vertical cylinder fitted with a frictionless piston and a set of stops as shown in the sketch
The central cubical area of an office building at sea level : the central cubical area of an office building at sea level has a floor area of 4000 ft2 and is occupied by 30 people
An m1 80 kg box lies on a friconless table and is : an m1 8.0 kg box lies on a friconless table and is attached to a m2 5.0 kg box by a light cord passing over a
A seaplane is flying at 100 mph through air at 45 f at what : a seaplane is flying at 100 mph through air at 45 f. at what distance from the leading edge of the underside of the
Resistors produced by a certain firm are marketed as 10-ohm : resistors produced by a certain firm are marketed as 10-ohm resistors. however the actual resistances of the resistors

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd