Air enters a converging-diverging nozzle at 700 kpa 240 k

Assignment Help Mechanical Engineering
Reference no: EM13634813

Air enters a converging-diverging nozzle at 700 kPA, 240 K, and Ma = 0.3. The inflow nozzle area is 13 cm2 and the outflow nozzle area is 8 cm2. Use k = 1.4, R = 0.28 kJ/kg*K and Cp = 1.005 kJ/kg*K for air as an ideal gas.

a. Determine the inflow velocity in m/s

b. What back pressure will produce supersonic outflow?

Reference no: EM13634813

Questions Cloud

An ideal gas contained in a piston-cylinder assembly is : an ideal gas contained in a piston-cylinder assembly is compressed isothermally in an internally reversile
A coin is tossed four times show the sample space and find : a coin is tossed four times. show the sample space and find the probability of getting a simple event of three heads
The number of chocolate chips in an 18-ounce bag of : the number of chocolate chips in an 18-ounce bag of chocolate chip cookies is normally distributed with a mean of 1250
The distribution of the annual incomes of a group of middle : the distribution of the annual incomes of a group of middle management employees approximated a normal distribution
Air enters a converging-diverging nozzle at 700 kpa 240 k : air enters a converging-diverging nozzle at 700 kpa 240 k and ma 0.3. the inflow nozzle area is 13 cm2 and the
Two cards are drawn without replacement from a standard : two cards are drawn without replacement from a standard deck of fifty-two cards. find the probability of these
A bank wishes to estimate the mean credit card balance : a bank wishes to estimate the mean credit card balance owed by its customers. the population standard deviation is
If the coefficient of static friction between the beam and : the uniform beam of mass 40 kg is supported by the rope which is attached to the end of the beam wraps over a rough peg
What flow rate of natural gas in cubic feet per hour would : what flow rate of natural gas in cubic feet per hour would be required to serve a 150000 btuhr output capacity

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the temperature of the environment were 33o c what rate

most of the energy we consume as food is converted to thermal energy in the process of performing all our bodily

  A ball is thrown vertically up with a velocity of 91 ftsec

a ball is thrown vertically up with a velocity of 91 ftsec at the edge of a 190-ft cliff. calculate a the height h to

  Assignment 1problem 1determine the analytical solution for

assignment 1problem 1determine the analytical solution for the maximum stress of the beam shown compare with stress

  An interest rate of 10 compounded continuously is desired

an interest rate of 10 compounded continuously is desired on an investment of 15000. how many years will be required to

  The reactor was empyu at the start of the experiment if

a solution containing bacteria at a concetration of .001gl was fed to a semibatch reactor. the nutrient was in excess.

  Explain aeronautical engineering module - mechanics

High school Yr 12 aeronautical Engineering Module - mechanics, PLease help- i seem to get the incorrect answer but didn't know where i have gone wrong?

  The specifications for an automobile fuel pump state that

the specifications for an automobile fuel pump state that it should pump 1 l of gasoline in 40 seconds with a suction

  Expands adiabatically to 40 bar 235 k with no significant

argon gas enters a turbine operating at steady state at 100 bar 325 k and expands adiabatically to 40 bar 235 k with no

  Find the maximum shear stress and normal stress for the

a quartz sphere of 20mm diameter is pressed into a flat thick carbon steel plate with a force of 5 n. find the maximum

  Dtermine the mass rate of water flowing kgs height

a 5 cm orifice meter is being used to measure the flowrate of 70 degree c water. the mercury manometer shows a height

  Prepare a case study based industrial visit report

Overview of the company which includes company background, major businesses, annual production, and major customers involved.

  However the material contains cracks through the wall

a pressure vessel made of aluminum alloy 2024?t351 sy 325 mpa and kc 36 mpa?m12 is manufactured for a safety factor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd