Air can be assumed to be an ideal gas with a

Assignment Help Mechanical Engineering
Reference no: EM13623902

A well-insulated tank contains 1 mole of air at 2 MPa and 673 K. It is connected via a closed valve to an insulated piston/cylinder device that is initially empty. The piston may be assumed to be frictionless. The volumes of the piping and valve are negligible. The weight of the piston and atmospheric pressure are such that the total downward force can be balanced with gas pressure in the cylinder of 0.7 MPa. The valve between the tank and piston/cylinder is cracked open until the pressure is uniform throughout. The temperature in the tank is found to be 499.6 K. Air can be assumed to be an ideal gas with a temperature-independent heat capacity CP = 29.3 J/mol-K.

What is the number of moles left in the tank at the end of the process?

Write and simplify the energy balance for the process. Determine the final temperature of the piston/cylinder gas.

Reference no: EM13623902

Questions Cloud

1 determine for each case whether the substance is a : 1 determine for each case whether the substance is a compressed liquid superheated vapor or saturated mixture using the
The pump draws 20 kw of power and operates at 50 efficiency : consider a pump that moves q0.1 m3s of oil s.g. 0.8 from an open reservoir through a 10 cm diameter pipe. the pump
Consider a cross flow of water saturated water that comes : consider a cross flow of water saturated water that comes at 20c with a velocity of 5 ms on the surface of a
A circular coil of wire consisting of 100 turns each of : a circular coil of wire consisting of 100 turns each of radius 8.0 cm carries a current of 0.40 a. what is the
Air can be assumed to be an ideal gas with a : a well-insulated tank contains 1 mole of air at 2 mpa and 673 k. it is connected via a closed valve to an insulated
The balance point of the cell in open circuit is 763 cm : potentiometer used for the determination of internal resistance of a 1.5 v cell. the balance point of the cell in open
A jet-propelled object has a straight-line motion according : a jet-propelled object has a straight-line motion according to the equation x 2 t2 - 2t - 2 where x is in meters and t
An automobile tire with a volume of 06m3 is inflated to a : an automobile tire with a volume of 0.6m3 is inflated to a gage pressure of 200 kpa. calculate the mass of air in the
Determine the value of x what might you do if you failed to : a potentiometer circuit for comparison of two resistances. the balance point with a standard resistor r 10.0nbspomega

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd