After the pressures but not the temperature in the two

Assignment Help Mechanical Engineering
Reference no: EM13631608

An isolated chamber with rigid walls is divided into two equal compartments, one containing steam at 10 bar and 370oC, and the other evacuated. A valve between the compartments is opened to permit steam to pass from one chamber to the other.

a. After the pressures (but not the temperature) in the two chambers have equalized, the valve is closed, isolating the two systems. What is the temperature and pressure in each cylinder?

b. If the valve were left open, an equilibrium state would be obtained in which each chamber has the same temperature and pressure. What is this temperature and pressure?

Reference no: EM13631608

Questions Cloud

Why does necking occur during a tensile test use your : why does necking occur during a tensile test? use your knowledge of engineering stress and strain to explain the
The bullet remains embedded in the block which is observed : a 4.50g bullet is fired horizontally into a 2.35kg wooden block resting at the bottom of a 25 degree inclined surface.
If the power generated by the turbine is 75 mw determine : steam expands in a turbine steadily at a rate of 36048 kgh entering at 8 mpa and 600degc and leaving at 20 kpa as a
A muon and an antimuon are moving in opposite directions : a muon and an antimuon are moving in opposite directions with velocities of -0.7 c and 0.7 c respectively. when they
After the pressures but not the temperature in the two : an isolated chamber with rigid walls is divided into two equal compartments one containing steam at 10 bar and 370oc
Determine a the exergetic effectiveness and b the exergy : refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
A rigid 10 m3 tank contains water initially at 120degc with : a rigid 1.0 m3 tank contains water initially at 120degc with 50 liquid and 50 vapor by volume. a pressure-relief valve
A well-insulated rigid tank contains 8 kg of a saturated : a well-insulated rigid tank contains 8 kg of a saturated liquid-vapor mixture of water at 100 kpa. initially three
Consider the following give your answers correct to two : consider the following. give your answers correct to two decimal places.a find the standard score z such that the area

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd