Additional engine weight is added for each horsepower

Assignment Help Civil Engineering
Reference no: EM13666974

A vehicle manufacturer is considering an engine for a new sedan (CD = 0.3, Af = 21 ft2). The desired maximum speed is 100 mi/h at sea level (? = 0.002378 slugs/ft3). However, the designer selected an underpowered engine of light weight (the car with the engine weigh 2100 lb) that achieved a maximum speed of 90 mi/h. Determine the required engine power and the final weight of the car if it is to achieve 100 mi/h speed, assuming that 2 lb of additional engine weight is added for each horsepower of additional engine power..

Reference no: EM13666974

Questions Cloud

What is the minimum thickness of the film : A thin film of soap with n = 1.39 hanging in the air reflects dominantly red light with λ = 651 nm. What is the minimum thickness of the film? Now this film is on a sheet of glass, with n = 1.46. What is the wavelength of the light in air that will n..
Decide the temperature at which the rms speed : Decide the temperature at which the rms (root-mean-square) speed of an He atom equals 990 m/s. What is the rms speed of He on the surface of a certain star, where the temperature is 5374 K? 75. Two narrow slits are illuminated with a laser with a wav..
Assume pore contain only oil and water : Assume pore contain only oil and water
The time-scale for a point source injected mid-way : The time-scale for a point source injected mid-way between two impermeable boundaries to become uniformly mixed across the section is given by the rule-of-thumb
Additional engine weight is added for each horsepower : Additional engine weight is added for each horsepower of additional engine power..
Resulting force per unit length experienced with these wires : Two long parallel straight wires are 0.300 m apart and each carries a current of 2.70 A in the same direction. Compute the magnitude of the resulting force per unit length experienced with these wires.
Compute the velocity of a free-falling parachutist : Compute the velocity of a free-falling parachutist using Euler's method for the case where m = 80 kg and c = 10 kg/s. Perform the calculation from t = 0 to 20 s with a step size of 1 s. Use an initial condition that the parachutist has an upwar..
How thick is the piece of paper : Light of wavelength 579 nm shines down on two glass plates, spaced at one end with a thin piece of paper. Looking down on the plates (the figure shows a side view only), 26 bright interference fringes are observed across the top plate by a dark fring..
Balance to sustain an aeroplane in steady : List the forces and moments that must be in balance to sustain an aeroplane in steady, straight and level flight.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the longitudinal and transverse stresses

Calculate the overall modulus of the composite, explaining your calculations and the assumptions you have made when it is loaded:

  Determine what is the maximum speed attained

The coefficient of rolling resistance can be taken to be a constant for all speeds, equal to 0.008. If the cyclist is coasting down a 6% grade, what is the maximum speed attained

  Find the magnitude of the particles position and velocity

The position of a particle P moving in the horizental plane is described by r(t)= (5t^2 i +2te^0.1t j) m. Find the magnitude of the particle's position, velocity, and acceleration at time t=2 sec.

  A root of the linear portion of the stress strain relation

A 32mm rebar with a guage length of 200mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in table below.

  Define the f by m ratio in context of biological treatment

Define the f/m ratio in the context of biological treatment of wastewater, and relate the f/m ratio to the exponetial growth and declinign growth phases of a bacterial culture.

  Briefly outline with the use of neat labelled sketches

It is proposed to make a new pedestrian access running directly south from University Square to Silvertown. The physical barriers that need to be overcome are the Royal Docks and the City Airport runway.

  What would be the co concentration in the box

GIVEN: A simple way to model air pollution over a city is with a box model that assumes complete mixing and limited capability for the pollution to disperse horizontally or vertically except in the direction of the prevailing winds (for example, a to..

  How many gallons of water per cubic yard should be added

given moisture contents of 5%, 9%, 14%, 22% and 25% with corresponding weights of 3.1, 3.42, 3.78,3.85, 3.77 lbs. of the compacted soil. (specific gravity =2.7)(compaction test using compaction mold of 1/30 ft^3).

  When finding the projection of p onto q what to do with 15n

Force P is directed from point A(5,10,3) towards point B(1,-2,5) and has a magnitude of 15N. Vector Q=6i+2j-5k. When finding the projection of P onto Q what do you do with the 15N

  Determine what is the rectangles product of inertia

Two identical squares (each18x18mm ) sit on the x axis and are joined at the y axis to form a rectangle. What is the rectangle's product of inertia

  What will be the least pillar dimension

A 2in cube coal specimen, which was tested in a lab, failed at 8,000lb.  A set of main entries is to be designed through the 5ft seam from which the specimen was extracted.  If there is 500ft of overburden, and assuming a 50% recovery, what will be t..

  Determine the maximum load p that the member can support

A stainless steel tube with an outside diameter of 59 mm and a wall thickness of 5 mm is used as a compression member. If the axial normal stress in the member must be limited to 220 MPa, determine the maximum load P that the member can support.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd