Actual thermal conductivity of the carbon nanotube

Assignment Help Mechanical Engineering
Reference no: EM13947387

Physicists have determined the theoretical value of the thermal conductivity of a carbon nanotube to be kcn,= 5000 W/m · K.

(a) Assuming the actual thermal conductivity of the carbon nanotube is the same as its theoretical value, find the thermal contact resistance, Rt,c, that exists between the carbon nanotube and the top surfaces of the heated and sensing islands in Example 3.4 .

(b) Using the value of the thermal contact resistance calculated in part (a), plot the fraction of the total resistance between the heated and sensing islands that is due to the thermal contact resistances for island separation distances of 5 µ,20 µ,m.

Reference no: EM13947387

Questions Cloud

Induction heating coil experiences uniform volumetric : A very long rod of 5-mm diameter and uniform thermal conductivity k = 25 W/m · K is subjected to a heat treat- ment process. The center, 30-mm-long portion of the rod within the induction heating coil experiences uniform volumetric heat generation..
Write a statement to create a view that selects all fields : Write a statement to add a check constraint to the above defined table, which guarantees that values entered in the Class field can only be limited to the following strings: Open, Spec, and Priv.
Explain decision maker go get information future cash flows : As you continue your discussions on other capital budgeting considerations, please explain where would a decision maker go to get information about future cash flows for a proposed project? Examples to illustrate your points are greatly appreciated..
What was the amount of cash paid in taxation during year two : The tax liability in the statement of financial position at the end of Year 2 was £10m. What was the amount of cash paid in taxation during Year 2?
Actual thermal conductivity of the carbon nanotube : Physicists have determined the theoretical value of the thermal conductivity of a carbon nanotube to be kcn,T = 5000 W/m · K. (a) Assuming the actual thermal conductivity of the carbon nanotube is the same as its theoretical value, find the thermal..
What is the percent change in the multifactor productivity : What is the companys labor hours productivity and what is its multifactor productivity - What is the percent change in the multifactor productivity if the initial process used is the one without the rework capability and is then replaced by the pro..
How might you interconnect those two areas : Some say that one of the great problems in networking is the lack of enforceable standards, so that the equipment of any manufacturer can work with any other manufacturer "off the shelf". Do you agree? Justify your answers
Prepare a statement of cash flow from operations : During the year the trading stock has increased by £1m, trade debtors have decreased by £3m and trade creditors have decreased by £2m. Prepare a statement of cash flow from operations.
What is the warning that the author offers for viewers : D'Alleva defines formal analysis but adds a warning for viewers attempting to describe works of art. What is the warning that the author offers for viewers

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the various methods of how safety is measured and

evaluate the various methods of how safety is measured and the current safety data systems and compare and contrast

  Refrigerant 134-a enters a condenser of a residential heat

refrigerant 134-a enters a condenser of a residential heat pump at 800 kpa and 35oc at a rate of 0.018 kgs amd leaves

  Assume the blood is a bingham plastic

The apparent viscosity of human blood has been reported as 6.49 cP at a shear rate of 10 s^-1, and 4.66 cP at a shear rate of 80 s^-1. Assuming that blood is a non – Newtonian fluid, estimate the volumetric flow through a capillary of diameter 1 mm w..

  Shell-and-tube heat exchanger is used to cool flow of steam

A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..

  A motor has a disk mounted on its shaft

A motor has a disk mounted on its shaft. The disk has a diameter of 1 foot and weighs 60 pounds. Starting from rest, the motor rotates at 350 rpm after 5 seconds. If the motor has a 92% efficiency, determine the input power in watts.

  Determine how much time is required for the ball to reach a

a 4-lb ball b is traveling around in a circle of radius r1 3 ft with a speed vb1 6 fts. if the attached cord is

  Phase of the product development process

Identify and understand each phase of the product development process: The assignment includes the practical application of the first few phases of a PD process.

  Calculate the coefficient of performance of a carnot heat

an ideal vapor-compression heat pump cycle with refrigerant 134a as the working fluid provides heating at a rate of 15

  Heat transfer and work transfer for the two-step process

Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobaric ally until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperatur..

  High pressure and low pressure turbines are used

Reheat, where high pressure and low pressure turbines are used, is added to a simple steam cycle to increase the steam quality at the location where the steam exits the low pressure turbine and goes to the condenser. Consider a steam cycle where the ..

  Determine the minimum mass in kg of a 24 in long tension

determine the minimum mass in kg of a 24 in long tension member that must support a load of 1000 lbs manufactured from

  Compute the desities of totally crystalline and totally

the density and associated percent crysallinity for two nylon 66 materials are shown as follows compute the desities of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd