A very long cylinder diameter 1mm is placed perpendicular

Assignment Help Mechanical Engineering
Reference no: EM13625962

A very long cylinder (diameter 1mm) is placed perpendicular to a steady airstream whose velocity is 10 m/sec. The cylinder is heated electrically at 100 watts/meter span. At what distance downstream is the rms temperature fluctuation in the wake of the cylinder reduced to 1?C? Assume that the distribution of the mean temperature difference in the wake is similar to the distribution of the mean velocity defect. For air at room temperature and pressure, ? = 1.25kg/m3, cp = 103joule/kg?C. Hint: the dimension of the heating is joules/sec/meter. The dimension of the heat flux through position x is (?cp)T times the velocity times the integrated profile in y, which will have a dimension of length. The dimensions of the heating and the dimensions of this heat flux are the same.

Reference no: EM13625962

Questions Cloud

The phase angle of an rlc series circuit with a capacitive : the phase angle of an rlc series circuit with a capacitive reactance of 40 omega a resistor of 100 omega and a certain
Assume ideal gases with a constant heat capacity of cp 293 : a vortex tube has an inlet air flow at 300 k and 5 bar. a vortex tube with 1 mole of input air outputs 0.8 moles 1 bar
A 120 g ball attached to a spring with spring constant 29 : a 120 g ball attached to a spring with spring constant 2.9 nm oscillates horizontally on a frictionless table. its
If the flash drum is maintained at 06 mpa what fraction of : 1 for a separations process it is necessary to determine the vle compositions of a mixture of ethyl bromide and
A very long cylinder diameter 1mm is placed perpendicular : a very long cylinder diameter 1mm is placed perpendicular to a steady airstream whose velocity is 10 msec. the cylinder
In bohr model of hydrogen atom the average kinetic energy : in bohr model of hydrogen atom the average kinetic energy of the electron in the first excited state is four times the
An irreversible first-order reaction gave 95 conversion in : an irreversible first-order reaction gave 95 conversion in a batch reactor in 20 min.a. what would be the conversion of
Consider a spark ignition combustion engine with two : consider a spark ignition combustion engine with two possible configurartion for turbocharging. configuration a is
Consider an electron in a box if the energy of the first : consider an electron in a box. if the energy of the first excited state is 10 evlarger than the energy of the ground

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd