A valve is opened allowing air to flow into the tank until

Assignment Help Mechanical Engineering
Reference no: EM13610675

At 100 lbf/in2, saturated vapor H2O flows in a pipe. A valve is opened to vent a small amount to the atmosphere. Assuming no changes in kinetic energy and no heat transfer, what is the temperature as it leaves the valve? A line with ammonia that flows at 180 psi, 140oF is attached by a valve to a tank. The tank initially has ammonia is stored in it at 20 psi, 80oF in a 20-ft3 tank The valve is opened, and mass flows in until the tank is half full of liquid, by volume at 80oF. What is the heat transferred from the tank during this process. An evacuated 1-ft3 tank is connected by a valve to an air supply line flowing air at 120 psi and70oF. A valve is opened allowing air to flow into the tank until the pressure reaches 90 psi. How much mass flowed into the tank and what is its final temperature? Assume the process is adiabatic.

Reference no: EM13610675

Questions Cloud

You have an opportunity to purchase the waiting line cafe a : you have an opportunity to purchase the waiting line cafe a busy shop near your office. the owner is asking 80000.
Where does the company disclose its revenue recognition : finding financial information refer to the financial statements of urban outfitters given in appendix c at the end of
Charley companys assembly department has materials cost at : charley companys assembly department has materials cost at 3 per unit and conversion cost at 6 per unit. there are 9000
Determine the range of values of alpha for which the : three forces are applied to a bracket as shown. the directions of the two 30 n forces may vary but the angle between
A valve is opened allowing air to flow into the tank until : at 100 lbfin2 saturated vapor h2o flows in a pipe. a valve is opened to vent a small amount to the atmosphere. assuming
Jm shoe chief executive officer of jolsen international a : jim shoe chief executive officer of jolsen international a multinational textile conglomerate has recently een
Assume that a quality characteristic is normally : assume that a quality characteristic is normally distributed. an x-bar control chart is constructed with 3 sigma
How far does the motorcycle travel from the moment it : a motorcycle is following a car that is traveling at constant speed on a straight highway. initially the car and the
Jake company reports the following for july august : jake company reports the following for july august september. sales july 26000 august 34000 september 38000.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd