User Account

All Pages

A value that causes the 24 hr average velocity to be 20 ms

Assignment Help Mechanical Engineering
Reference no: EM13611410

A wind turbine with a swept area of 1000 m2 operates with 56% efficiency under STP conditions. At the location of the windmill, there is no wind between 1800 and 0600. At 0600, the wind starts up and its velocity increases linearly with time from zero to a value that causes the 24 hr average velocity to be 20 m/s. At 1900 the wind stops abruptly. What is the maximum energy the windmill can generate in one year?

Reference no: EM13611410

Questions Cloud

Esther is a physician with her own practice she has : esther is a physician with her own practice. she has developed contracts with several large employers to perform
Luthan company uses a predetermined overhead rate of 2340 : luthan company uses a predetermined overhead rate of 23.40 perdirect labor-hour. this predetermined rate was based on
The only information you have about a proposed site for a : the only information you have about a proposed site for a wind farm is that the wind blows at speeds above 25 ms 90 hrs
The following present value factors are provided for use in : the following present value factors are provided for use in this problem present value present value of an periods of 1
A value that causes the 24 hr average velocity to be 20 ms : a wind turbine with a swept area of 1000 m2 operates with 56 efficiency under stp conditions. at the location of the
The water leaves the tube leaves at the 1mpa and 300oc with : water at 1mpa and 65oc enters a tube of a boiler which has a constant 160mm inside-diameter. the water leaves the tube
Calculate the cash dividends required to be paid for each : calculate the cash dividends required to be paid for each of the following preferred stock issuesrequireda the
A student takes a calculus midterm and a history midterm : a student takes a calculus midterm and a history midterm. the mean and standard deviation on the calculus midterm are
When an object falls and hits the floor without bouncing : when an object falls and hits the floor without bouncing off the floor the normal force of the floor on the object

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find a cylindrical container

Find a cylindrical container that is large enough that it takes at least one minute to drain (you may have to create an opening at or near the bottom that gives the right behavior.

  Problem a tension link shown to the right is used in

problem a tension link shown to the right is used in earth-moving equipment and is subjected to cyclic stresses varying

  What is a 90 percent confidence interval

What is a 90 percent confidence interval for the standard deviation of the thickness of a washer produced by this procedure?

  Electric-circuit which is called a phase

Shows an electric-circuit which is called a phase-lag network. Derive the transfer function and consider the above bock-diagram of figure (3). You are now required to derive the transfer function Y(s)/R(s), by using the signal flow graph meth..

  Find the tangential component of the acceleration when the

a partivcle along a plane cirve from point a to a point b. the path length between a and b is 60 in. the speed at a is

  What two maintained tools will hurt an automotive technician

what two maintained tools will hurt an automotive technicians on the job performance?

  An accelerometer indicates that part of a machine element

an accelerometer indicates that part of a machine element is vibrating harmonically at 82cps with a maximum

  Determine the mass flow rate of the air

Determine the mass flow rate of the air passing through this engine and the rates of heat addition and rejection when this engine produces 1000 hp. Assume constant specific heats at room temperature.

  A tube with elastic modulus of 75 gpa is used to support a

a tube with elastic modulus of 75 gpa is used to support a compressive load. it is required that this tube must not

  Problem a compound cylinder is composed of a tube of 250mm

problem a compound cylinder is composed of a tube of 250mm internal diameter at 25mm wall thickness. it is shrunk on to

  Determine the power needed to drive the low speed turbine

determine the power needed to drive the low speed turbine given maximum velocity in the test section 140 mih with 12 x

  The end of the lever arm moves 50cm and the load moves 20cm

in a system a lever needs and effort of 200n to lift a load of 350n. the end of the lever arm moves 50cm and the load

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd