A universitys campus has 20000 computers with cathode-ray

Assignment Help Mechanical Engineering
Reference no: EM13627520

A university's campus has 20,000 computers with cathode-ray tube monitors that are powered-up even when the computer is not being used. This type of monitor is relatively inefficient, and it draws more power than a flat panel display.

(a) If each cathode-ray tube monitor draws 0.1 kW of power over the course of a year, how much energy has been consumed?

(b) At the cost of seven cents per kW-h, how much does it cost the university each year to keep these monitors powered-up?

(c) On average, a computer monitor that has the automatic sleep feature enabled will consume 72% less energy than one that is continually powered. What is the cost savings associated with enabling this feature on all of the university's computers?

Reference no: EM13627520

Questions Cloud

Geothermal energy systems extract heat that is stored below : geothermal energy systems extract heat that is stored below the earths crust. for every 300 ft below ground the
As the container expands the pressure increases by a factor : a container with volume 213 cubic cm is heated and allowed to expand to 1.44 times the original volume. as the
Finally the air is isochorically cooled returning to its : a mass of 1.5kg of air enters a combustion chamber at atmospheric conditions of 100 kpa and 25 degrees c at state 1.
The average weight of adult men is 181 pounds with a : the average weight of adult men is 181 pounds with a standard deviation of 40 pounds.thirty five 35 men were asked
A universitys campus has 20000 computers with cathode-ray : a universitys campus has 20000 computers with cathode-ray tube monitors that are powered-up even when the computer is
A uniform line charge of linear charge density l 100 ncm : a uniform line charge of linear charge density l 10.0 ncm extends from x 5 m to x 8 m. the magnitude of the electric
A given liquid has a temperature 178 celcius at a pressure : a given liquid has a temperature 178 celcius at a pressure of 47 mpa. if the enthalpy of the saturated liquid at the
A printing pigment solution having a viscosity of 005 n s : a printing pigment solution having a viscosity of 0.05 n s m2 and the yield stress of 0.6 nm2 flows in a three meter
A disk of radius b 100 cm has a total charge of q 80 pc : a disk of radius b 10.0 cm has a total charge of q 8.0 pc. what is the surface charge density?a 2.5x102 cm2b 8.0x

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A boiling-water-type nuclear fission reactor has shut down

a boiling-water-type nuclear fission reactor has shut down the backup pumps have failed and emergency cooling water

  Draw the shear force diagram for the beam

Draw the shear force diagram for the beam and determine the position and magnitude of the maximum bending moment.

  If the probe surface has an emissivity of 08 and it does

a spherical interplanetary probe of 0.5-m diameter contains electronics that dissipate 150 w. if the probe surface

  Te acceleration of a particle is defind by the relation a

the acceleration of a particle is defind by the relation a - 0.8 v where a is expressed in ms2 and v ms. knowing

  Air is compressed under steady flow conditions see figure

air is compressed under steady flow conditions see figure q3. the power input to the compressor is 3 kw. during the

  Assume the refrigerant is a saturated vapor at the

a vapor-compression refrigeration cycle employed in a heat pump uses refrigerant r-134a and provides 15 kw of heating.

  Calculate the out of balance force

a gear of mass 2.5kg rotates ar 1500rpm.due to an error in manufacture the centre of gravity of the wheel is displaced 0.5mm from the axis of rotation. calculate the out of balance force.

  Given n1000 lb e30x106 psi upsilon03 l4 ft gamma0283 lbin3

given n1000 lb e30x106 psi upsilon0.3 l4 ft gamma0.283 lbin3 and a 4x4 hollow square tube beam cross section with a

  Determine the mass flow rate

(a) Draw and label a schematic of the system. (b) Determine the mass flow rate (kg/s) of water vapor neededand (c) the rate of exergy destruction (kW)

  Steam at 16mpa and 400 degrees c is contained in a rigid

steam at 1.6mpa and 400 degrees c is contained in a rigid box. the system is then cooled to 200 degrees c. compare the

  What speed will the sleeve attain

what speed will the sleeve attain? The temperature oƒ the sleeve remains constant.

  The second step is a constant pressure process to 1500k

1.5 kg of ethane at 150 kpa 300k is heated in a two-step process using a source at 1600k. the first step is a constant

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd