A thin metal cylinder contains an ideal gas the cylinder

Assignment Help Mechanical Engineering
Reference no: EM13630188

A thin metal cylinder contains an ideal gas. The cylinder has a cross sectional area of 100 cm^2. The surroundings outside the cylinder are maintained at 25 degrees C and 101 kPa. A piston caps one side of the cylinder. The piston is attached to a spring; it is also exposed to the atmosphere. Initially, the ideal gas has a pressure of 300 kPa and 1000 cm^3. A catch holds the piston so that the spring sits in its resting position. There is a lot of friction between the cylinder wall and the piston head. The catch is removed and the gas slowly expands, eventually compressing the spring 5 cm.

a) What is the final pressure of the ideal gas?

b) What is the spring constant in N/m? How much work did the ideal gas do to compress the spring?

c) How much work did the ideal gas do to move the atmosphere out of the way?

d) How much of the work done by the ideal gas was dissipated through friction?

Reference no: EM13630188

Questions Cloud

Find the aproximate dimensions of a pin so that the : find the aproximate dimensions of a pin so that the bearing and tearout of the plate happen simotaniously menaing the
For the position of the box given determine the force in : a winch at point b is used to slide a box up a chute cd in a warehouse.the box wieghs 530lb and fits loosely against
If the test indicates that a person does not have the : the incidence of a certain disease in the population is estimated to be 1.5 . that is the probability that a randomly
One process follows arrhenius behavior ie at a given load : one process follows arrhenius behavior i.e. at a given load the inverse of time to fracture has been shown to increase
A thin metal cylinder contains an ideal gas the cylinder : a thin metal cylinder contains an ideal gas. the cylinder has a cross sectional area of 100 cm2. the surroundings
When a capacitor has a charge of magnitude 57 microc on : when a capacitor has a charge of magnitude 57 microc on each plate the potential difference across the plates is 11 v.
If the test indicates that a person does not have the : the incidence of a certain disease in the population is estimated to be 1.5 . that is the probability that a randomly
Assume adiabatic operation what is the ratio of chilled air : a device with no moving parts provides a steady stream of chilled air at -25c and 1 bar. the feed to the device is
An applicant needs a minimum combined score of 1500 to gain : the gre combined scores for students applying to an engineering schools graduate program are normally distributed with

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd