A tank open to the atmosphere initially contains 2 lb of

Assignment Help Mechanical Engineering
Reference no: EM13629622

A tank open to the atmosphere initially contains 2 lb of liquid water initially at 80°F and 0.4 lb of ice initially at 32°F. All of the ice melts as the tank contents attain equilibrium. If no significant heat transfer occurs between the tank contents and their surroundings, determine the final equilibrium temperature, in °F. For water, the specific enthalpy change for a phase change from solid to liquid at 32°F and 1 atm is 144 Btu/lb.

Reference no: EM13629622

Questions Cloud

Determine a the mass flow rate through the nozzle b the : air enters a nozzle steadily at 300 kpa 200degc and 45 ms and leaves at 100 kpa 180 ms. the inlet area of the nozzle
A supersonic nozzle is also a convergent-divergent duct : a supersonic nozzle is also a convergent-divergent duct which is fed by a large reservoir at the inlet to the nozzle.
The electric potential at a position located a distance of : the electric potential at a position located a distance of 18.9 mm from a positive point charge of 8.70times10-9 c and
Air at 200 kpa and 950 k enters an adiabatic nozzle at low : air at 200 kpa and 950 k enters an adiabatic nozzle at low velocity and is discharged at a pressure of 80 kpa. if the
A tank open to the atmosphere initially contains 2 lb of : a tank open to the atmosphere initially contains 2 lb of liquid water initially at 80degf and 0.4 lb of ice initially
A 85cm3 block of iron is removed from an 800oc furnace and : 1 a 85cm3 block of iron is removed from an 800oc furnace and immediately dropped into 200 ml of 20oc water. what
Percent confident of the results with an error of plus or : if a researcher wishes to conduct a study about how much consumers in a target market segment intend to spend on a type
If the heat lost to the surroundings amounts to 10 of the : steam flows steadily through an uninsulated turbine. the inlet conditions of the steam are 6 mpa 400degc and 80 ms and
The load is supported by the four 304 stainless steel wires : the load is supported by the four 304 stainless steel wires that are connected to the rigid members ab and dc.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd