A tank fitted with an electrical resistor holds 2 kg of

Assignment Help Mechanical Engineering
Reference no: EM13630013

A tank fitted with an electrical resistor holds 2 kg of Nitrogen (N2), Initially at 1 bar. Over a period of 10 minutes, electricity is provided to the resistor at a rate of 120 W. During the same period, a heat transfer of magnitude 12.6 kJ occurs from the Nitrogen to its surroundings. The temperature at the end of the ten minute interval is 67 degrees Celsius. Assume ideal gas behavior for the Nitrogen and determine (a) the initial temperature, in degrees Celsius, and (b) final pressure, in MPa.

Reference no: EM13630013

Questions Cloud

An 1820 kg car passes over a bump in a road that follows : an 1820 kg car passes over a bump in a road that follows the arc of a circle of radius 41.9 m.a what force does the
The fin array is exposed to air at tair 20 degrees c with : a fin array consists of 6 rectangular fins on a 2mm thick 100mm by 180mm plate. the array is made of aluminum and each
Define the physical uncontrolled seat including seat : a farm equipment manufacturer has a need to actively reduce the vibration of the operators seat using an electrodynamic
The dog starts running when the owners are d 80 m apart if : a dog runs back and forth between its two owners who are walking toward one another. the dog starts running when the
A tank fitted with an electrical resistor holds 2 kg of : a tank fitted with an electrical resistor holds 2 kg of nitrogen n2 initially at 1 bar. over a period of 10 minutes
A cheetah can accelerate from rest to 220 ms in 676 s a : a cheetah can accelerate from rest to 22.0 ms in 6.76 s.a assuming constant acceleration how far has the cheetah run in
A horizontal force f pushes a 10 kg block up a : a horizontal force f pushes a 10 kg block up a fricitionless ramp with a circular contour the radius of curvature of
Using a binomial table find the binomial probabilities px : using a binomial table find the binomial probabilities px associated with given n ratio and x. a. n6 ratio 0.10 p4 b.
Consider a cogeneration power plant modified with : consider a cogeneration power plant modified with regeneration. steam enters the turbine at 9 mpa and 400 c and expands

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Is there an economic case for renewable energy

Is there an economic case for renewable energy? This issue was recently a "hot topic" in the news, and you are referred to the following newspaper article for a representation from the media.

  A temperature measuring devise has been used to measure a

a temperature measuring devise has been used to measure a dynamic temperature change in a system. the system is no

  The steel bar has the orginal dimensions shown in the

the steel bar has the orginal dimensions shown in the third figure below. if it is subjected to an axial load of 50kn

  More heat is transferred until the pressure inside the

a piston cylinder device with a set of stops on the top initially contains 3 kg of air at 200kpa and 27 degrees

  The pan is hot 80c and the room is cool 20c calculate the

a hot surface on a stovetop faces upwards. it is a pan whose diameter is 10 inches. the surface of the pan is dull with

  Based of thermodynamic considerations does this system work

one of your classmates claims to have invented a flow device to increase the superheat of steam. his claim is that he

  A vertical piston-cylinder assembly contains 03 kg of air

a vertical piston-cylinder assembly contains 0.3 kg of air k1.4 r287 jkgk initially at 155 kpa and 27 degree c. the is

  At the compressor inlet saturated vapor enters at -10 degc

consider an ideal vapor-compression refrigeration cycle. the refrigerator employs refrigerant 134a as the working fluid

  Determine the mass moment of inertia

A flywheel can be considered as being composed of a thin disc and a rim. The rim weighs 322 lb and has diameters of 24 in. and 30 in. The disc weighs 64.4 lb. Determine the mass moment of inertia about the centroidal axis about which the flywheel ..

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

  Kinetic and potential energy effects can be neglected

water vapor at 5 bar. 320 degree c enters a turbine operating at steady state with a mass flow rate of 1.5 kgs and

  A 25-hp 240-v 778-a shunt motor has an armature resstence

a 25-hp 240-v 77.8-a shunt motor has an armature resstence of 0.083 ohms and a field-circuit resistance of 125 ohms.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd