A supply pallet is dropped from an airplane

Assignment Help Mechanical Engineering
Reference no: EM13701747

A supply pallet is dropped from an airplane that is climbing at 30 degrees with an indicated air speed of 600ft/s while traveling at an altitude of 12,000 ft. Determine how long it takes for the pallet to reach the ground from it's release point.

Reference no: EM13701747

Questions Cloud

Determine the angular velocity w of the wheel : A wheel is rotating at a uniform clockwise speed of 2 rad/s when a variable torque is applied to its shaft at time t=0. As a result there is a clockwise angular acceleration \alpha which increases in direct proportion to the angle \Theta through whic..
Calculating the present value of a bond : Calculating the present value of a bond) If a corporate bond with a face value of $1,000 has 24 years to go until it matures, has a coupon interest rate of 5.7% and a yield to maturity (YTM) of 4.201%, what should be its price in the bond mark..
A heat engine rejects heat to the atmosphere : A heat engine rejects heat to the atmosphere. The temperature of the atmosphere is 80 F. Saturated liquid water enters the boiler at a rate of 1000 lbm/hour with pressure of 250 psia. The water exits the boiler as a saturated vapor at the same pressu..
How computer systems have changed the accounting : Demonstrate a basic understanding of how computer systems have changed the accounting profession -  they begin to understand the framework of how technology can assist accounting processes.
A supply pallet is dropped from an airplane : A supply pallet is dropped from an airplane that is climbing at 30 degrees with an indicated air speed of 600ft/s while traveling at an altitude of 12,000 ft. Determine how long it takes for the pallet to reach the ground from it's release point.
A corporate bond with a face value : If a corporate bond with a face value of $1,000 has 24 years to go until it matures, has a coupon interest rate of 5.7% and a yield to maturity (YTM) of 4.201%, what should be its price in the bond market (ie, PV)?
What is the static pressure in the reservoir : In a wind tunnel, a flow is sped up. In the reservoir, the velocity is approximately zero. In the test section, the air is at standard conditions with a flow speed of 30 m/s. What is the total pressure in the test section (in Pa)? What is the static ..
Find the heat transfer rate during the process : Nitrogen enters a nozzle steadily at 1.2mpa and 600k with a velocity of 30m/s the inlet area of the nozzle is 0.005m^2 the nitrogen leaves the nozzle at 298k with a velocity if 400m/s. find the heat transfer rate during the process?
Calculate depreciation using two different methods : What is the difference between valuation, depreciation, amortization, and depletion. Is it appropriate to calculate depreciation using two different methods? Why?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd