A street car line on the center of an 80 ft street makes

Assignment Help Civil Engineering
Reference no: EM13531123

1.AB has evenly distributed load of 6 kn/m and is 8 m long and Cis 3 m down from B (@ angle), determine the reactions at A.

Also D is in the center of AB and determine the internalnormal force, internal shear, and internal moment at D.

Hint BC is a link or truss member

2.A street car line on the center of an 80 ft street makes a 75degrees 24' turn into another street of equal width. Thecorner curb line has R=12 ft. What's the largest R that canbe given a circular curve for the tract center line if the lawrequires it to be at least 10ft from the curb?

Reference no: EM13531123

Questions Cloud

What is the original unstretched length of the cable : A 57.0 kg skier is being pulled up a 13.0° slope by a steelcable. The cable has a cross-sectional area of 7.18 10-5 m2. The cable applies a force tothe skier
Determine the approximate drag coefficient for the parachute : A 5-m-diameter parachute of a new design is to be used to transporta load from flight altitude to the ground with an average verticalspeed of 3 m/s. The total weight of the load and theparachute is 200 N. Determine the approximate dragcoefficient for..
Do the same for saturated vapor steam in an adiabatic : Saturated liquid water is in an adiabatic compressor with inlet and outlet pressures of 100 kPa and 1 Mpa. The isentropic efficiency is 85%. Find the work input (kj/kg) and entropy generation (kj/ kg K).Do the same for saturated vapor steam in an adi..
What is the density of the rock before it blasted : You are given the following information about a dry-batchpaving operation. You are going to use one mixer that has a servicerate of 30 serives/hr. The dry-batch trucks you use forbringing concrete to the paver have an arrival rate of 7.5 arrivals/hr...
A street car line on the center of an 80 ft street makes : A street car line on the center of an 80 ft street makes a 75degrees 24' turn into another street of equal width. Thecorner curb line has R=12 ft. What's the largest R that canbe given a circular curve for the tract center line if the law requires it..
Knowing that the coefficient of restitution between the : A 2-lb sphere A is moving to the left with a velocity of 40 ft/swhen it strikes the inclined surface of a 5-lb block B which is atrest. The block is supported by rollers and is attached to a springof constant k=12 lb/in.
Determine the required capacity of the motor of the : A step-type escalator as shown is designed to transport 120 persons per minute at a constant speed v=1.5 ft/s. The overall efficiency of the escalator is estimated to be 70%, and a 200% overload is to be allowed. Assuming that the average weight per ..
What is the underflow flow rate : A settling tank in a water treatment plant has an inflow of 2m3/min and a solids concentration of 2100 mg/L. The effluentfrom this settling tank goes to sand filters. Theconcentration of sludge coming out of the bottom (the underflow) is18,000 mg/L, ..
The mass flow rate of the refrigerant and : Refrigerant R-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at 120 kPa with a quality of 20 % and leaves at 120 kPa and -20°C. If the compressor consumes 450 W of power and the COP is 1.2

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the moisture content of product leaving the dryer

The tunnel is supplied with 1500 kg dry air/h at 50°C and 10% RH, and the air leaves at 25°C in equilibrium with the product at 50% RH. Determine the moisture content of product leaving the dryer and the final water activity.

  At what load would you expect the specimen to fracture

Three-point bending test was performed on an aluminum oxide specimen having a circular cross section of radius 5.5 mm; the specimen fractured at a load of 850 N when the distance between the support points was 50 mm.

  Calculate the steady-state pollutant concentration in lake

Conditions in the sewage pipe are Qs= 0.5 m^3/s, and Cs= 100mg/L. The pollutant is destroyed in the lake with a first-order rate constant of 0.2/d. The flow rate out of the lake is 5.0 m^3/s.

  Determine what is the adiabatic efficiency of the turbine

At the inlet the steam is at 1 MPa and 320 C, and leaves the turbine at 20 kPa. The work output of the turbine is measured to be 600 kJ/kg (of steam passing through the turbine).

  Determine the angular velocity of bar ab at displacement

Slider A moves in the horizontal slot with a constant speed v = 1.90 m/s for a short interval of motion. Determine the angular velocity of bar AB if the displacement xA = 90 mm, and the length L = 440 mm.

  Determine the flow rate and the normal depth in the channel

A reservoir discharges into a long trapezoidal channel with a bottom width of 20 feet, 3 to 1 side slopes, a bottom slope 0.001 and a roughness coefficient of 0.025 the reservoir surface is 10 feet above the invert at the channel entrance

  Calculate the amount of co produced in a rich combustion

Assume the only products are CO2, H2O, CO and N2. State results as the CO molar fraction of both wet and dry exhaust products ( wet exhaust products include H2) and dry exhaust products exclude it).

  Determine the minor loss coefficient k for a valve

A town is installing a new 10" main to carry drinking water. The only section remaining to be installed is a segment through the middle of town. However, the excavators discover an archaeological site.

  What do you mean by the term durability

What do you understand by the term durability? Compared to other considerations, how much importance should be given to durability in the design and construction of concrete structures?

  Give an equation for relative uncertainty of head loss

Equation for head loss in a pipe when it is laminar flow: head loss, h= (32*dynamic viscosity,u*pipe length,L*average velocity of fluid,V) / (gravitational acceleration,g*pipe diameter,D^2) Give an equation for relative uncertainty of head loss

  Determine the tension in each wire that are attached

A horizontal circular plate weighing 60-lb is suspended from three wires that are attached to a support at D and form 30 degree angles with the vertical. Determine the tension in each wire.

  Determine the angle that vo forms with vertical by rocket

If the rocket's decent parachute does not deploy and the rocket lands 340 ft from A, determine the angle (alpha) that vo forms with the vertical, the maximum height h reached by the rocket, and the duration of the flight.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd