A steel pipe of 12-in outer diamer is fabricated from

Assignment Help Mechanical Engineering
Reference no: EM13629914

A steel pipe of 12-in outer diamer is fabricated from 1/4-in-thick plate by welding along a helix that forms an angle of 25 degrees with a plane perpendicular to the axis of the pipe. Knowing that the maximum allowable normal and shearing stresses in the directions respectively normal and tangential to the weld are s = 12 ksi and t = 7.2 ksi, determine the magnitude P of the largest axial force that can be applied to the pipe.

Reference no: EM13629914

Questions Cloud

A sample is introduced into the chamber at 760 torr while : in many vacuum systems there is a gate valve consisting of a gasketed metal plate that acts to isolate the chamber
Two steel i-beams each with a mass of 100 kg are welded : two steel i-beams each with a mass of 100 kg are welded together at right angles and lifted by vertical cables so that
Determine the power input the rate of heat transfer from : air enters a compressor operating at steady state at 0.12 mpa 300k and a volumetric flow rate of 8 m3min. the air is
A ball is thrown straight down from the top of a cliff with : a ball is thrown straight down from the top of a cliff with a speed of 5 ms. the cliff-top is 20 m above ground level.
A steel pipe of 12-in outer diamer is fabricated from : a steel pipe of 12-in outer diamer is fabricated from 14-in-thick plate by welding along a helix that forms an angle of
The partition is now removed and the water expands to fill : a rigid tank is divided into two equal parts by a partition. one part of the tank contains 9.2 kg of compressed liquid
A researcher reported a correlation of 125 between an iq : a researcher reported a correlation of 1.25 between an iq test and grades in epy 6214. which one of the following
Cooling water circulates through a water jacket enclosing a : cooling water circulates through a water jacket enclosing a housing filled with electronic components. at steady state
A ball is thrown from atop a cliff with an initial speed of : problem 1 a ball is thrown from atop a cliff with an initial speed of 30 ms at an angle of 40o above the horizontal.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd