User Account

All Pages

A steam power plant utilizing the rankine cycle has the

Assignment Help Mechanical Engineering
Reference no: EM13641705

A steam power plant utilizing the Rankine cycle has the following particulars:

- Steam pressure and temperature at inlet of turbine are 40 bar and 400oC respectively.
- Condenser pressure is 0.1 bar.
- Steam mass flow rate 50 ton/hr.

a- Determine the power in kW and the thermal efficiency of the plant.

b- Compare the efficiency of the plant with that of the corresponding Carnot cycle.

Reference no: EM13641705

Questions Cloud

The appropriate pumps are used for the water leaving the : consider a regenerative cycle utilizing steam as the working fluid. steam enters the turbine at 3.5 mpa 400oc and
Given that x1x2x3 and x4 are independent random variable : given that x1x2x3 and x4 are independent random variable with mean 2 and variance 4 find ey and ez for y3x4-x10.2x3z
A model rocket is launched straight upward with an initial : a model rocket is launched straight upward with an initial speed of 70.0 ms. it accelerates with a constant upward
It is then reheated to 400oc and is then expanded to 10 kpa : consider a reheat cycle utilizing steam as the working fluid. steam enters the high pressure turbine at 3.5 mpa 400oc
A steam power plant utilizing the rankine cycle has the : a steam power plant utilizing the rankine cycle has the following particulars- steam pressure and temperature at inlet
Suppose a charge of -210 microc is at the origin and a : suppose a charge of -2.10 microc is at the origin and a charge of 2.90 microc is at the point 0 3.00 m.a find the
A microphone located at the opposite end of the rail : a hammer strikes one end of a thick iron rail of length 8.5 m. a microphone located at the opposite end of the rail
A binomial experiment is given decide whether you can use : a binomial experiment is given. decide whether you can use the normal distribution to approximate the binomial
At t 0 one toy car is set rolling on a straight track with : at t 0 one toy car is set rolling on a straight track with initial position 16.0 cm initial velocity -4.2 cms and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A horizontal uniform beam of length 3a and flexural

a horizontal uniform beam of length 3a and flexural rigidity ei is built-in at both ends. the beam carries a point load

  Determine the velocity and pressure profiles

Given an aerodynamic body, you have learned in Aerodynamics and Flight Mechanics how to apply the numerical Source Panel Method to this body to determine the velocity and pressure profiles along the surface of the body.

  A piston-cylinder contains air at a pressure of 500 kpa the

a piston-cylinder contains air at a pressure of 500 kpa. the piston movement is resisted by a spring and atmospheric

  The slotted link is pinned at o and as a result of the

the slotted link is pinned at o and as a result of the constant angular velocity theta dot 3rads it drives the peg p

  Determine the total mass in the tank at the initial and

the rigid tank illustrated in the figure has a volume of 0.06 m3 and initially contains a two-phase liquid-vapor

  Determine the power required to maintain the clean rooms

at steady state a refrigeration cycle maintains a clean room at 55degf by removing energy entering the rom by heat

  The pump draws 20 kw of power and operates at 50 efficiency

consider a pump that moves q0.1 m3s of oil s.g. 0.8 from an open reservoir through a 10 cm diameter pipe. the pump

  One kilogram of water contained in a sealed piston-cylinder

one kilogram of water contained in a sealed piston-cylinder assembly initially at 160degc and 200 kpa undergoes an

  The motion of a particle is defined by the equation x4t3 -

the motion of a particle is defined by the equation x4t3 - 5t2 5t and y5t2-15t where x and y are expressed in

  To move a differential drive robot forward at 1 ftsec how

to move a differential drive robot forward at 1 ftsec how fast must each wheel move? if the radius of each wheel is 1

  Determine the horizontal component of the absolute velocity

the 90-kg man dives from the 40-kg canoe. the velocity indicated in the figure is that of the man relative to the canoe

  Describe the fracture behaviour of the insulation tape

Cracks propagate when the stress intensity factor exceeds a critical value and describe the fracture behaviour of the insulation tape loaded with a small crack.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd