A steam pipe of 120 mm outside diameter and is covered with

Assignment Help Mechanical Engineering
Reference no: EM13644866

A steam pipe of 120 mm outside diameter and is covered with a 20 mm thick layer of calcium silicate insulation (k = 0.089W/m * K ). The surface temperature of the pipe is 800 K, and the ambient air and surrounding temperatures is 300 K.The convection coefficient is 5.5 W/m^2 *k and radiation coefficient is 10 W/m^2 * k. Determine the heat rate per unit length from the pipe (W/M) and the insulation outer surface temperature (K).

Reference no: EM13644866

Questions Cloud

If the level of confidence remains at 95 for the 720 : a company that manufacturers coffee for use in commercial machines monitors the caffeine content in its coffee. the
120 ohm resistor is in series with a 0140 h inductor and a : a 120 ohm resistor is in series with a 0.140 h inductor and a 0.500 micro f capacitor.a compute the impedance of the
What would happen to the width of the confidence intervals : a company that manufacturers coffee for use in commercial machines monitors the caffeine content in its coffee. the
A mechanical assembly consists of a rod with a bearing on : a mechanical assembly consists of a rod with a bearing on each end. the 3 parts are manufactured independently. the
A steam pipe of 120 mm outside diameter and is covered with : a steam pipe of 120 mm outside diameter and is covered with a 20 mm thick layer of calcium silicate insulation k
In a series r-l-c circuit the phase angle is 400 degrees : in a series r-l-c circuit the phase angle is 40.0 degrees with the source voltage leading the current. the reactance of
Let x be the number on the green die y be the number on the : a pair of fair 6-sided die one green one red are rolled. let x be the number on the green die y be the number on the
A 1000 kg rollercoaster moves in a vertical circular loop : a 1000 kg rollercoaster moves in a vertical circular loop of radius 10m as illustrated below. what is the magnitude of
If there were 2342 undergraduates how many of them had a : last years undergraduate distribution of gba was normally diatributed with a mean of 2.2 and a standard deviation of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd