A spherical meteor has a mass of 2kg and a diameter of 75mm

Assignment Help Mechanical Engineering
Reference no: EM13644120

1. A spherical meteor has a mass of 2kg and a diameter of 75mm. Assume that CD in air is 0.5.

a. What is the terminal velocity of the sphere in air near sea level at 20 deg C?

b. What is the Reynolds Number under these conditions?

c. How much kinetic energy does the meteor have under these conditions?

Reference no: EM13644120

Questions Cloud

Water and phenol are only partially miscible at temperature : water and phenol are only partially miscible at temperature below 66.8oc. in a mixture prepare at 29.6oc from 50.0g
Suppose a shipment of 50 cell phones has arrived from your : suppose a shipment of 50 cell phones has arrived from your supplier the samsing manufacturer. as the engineer for your
A if the vehicle has a speed of 200 ms what is the force of : a roller coaster vehicle has a mass of 500 kg when fully loaded with passengers. a if the vehicle has a speed of 20.0
According to the internal revenue service the mean tax : according to the internal revenue service the mean tax refund for the year 2013 was 3000. assume the standard deviation
A spherical meteor has a mass of 2kg and a diameter of 75mm : 1. a spherical meteor has a mass of 2kg and a diameter of 75mm. assume that cd in air is 0.5.a. what is the terminal
It has been suggested that rotating cylinders about 10 mi : it has been suggested that rotating cylinders about 10 mi long and 5.0 mi in diameter be placed in space and used as
Plot the temperature distribution along the line normal to : a 40 cm diameter pipe at 75 degree c is buried in a large block of portland cement. it runs parallel with a 15 degree c
Suppose that eight of the 25 radios are randomly selected : an electronics store has received a shipment of 25 table radios that have connections for an ipod or iphone. ten of
It has been suggested that rotating cylinders about 10 mi : it has been suggested that rotating cylinders about 10 mi long and 5.0 mi in diameter be placed in space and used as

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the strains in thick walled cylindrical vessel

Cylinder problem, Determine the strains in thick walled cylindrical vessel with inside diameter 1000 mm and outside diameter of 1400 mm

  A 456-kg girl is standing on a 141-kg plank both originally

a 45.6-kg girl is standing on a 141-kg plank. both originally at rest on a frozen lake that constitutes a frictionless

  The system has a partial condenser thus the distillate

a continuous steady state distillation column is fed a mixture that is 70 mol n-pentane and 30 mol n-hexane. feed rate

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  Determine the normal force r between the wheel

Determine the normal force R between the wheel and the horizontal surface. Neglect the weight of the horizontal shaft.

  Find the work done if the pressure between the initial and

a system has an initial volume of 10 ft3 and expands to a final volume of 20 ft3. the initial pressure is 15 psia. find

  What is differential levelling list the procedure for

what is differential levelling? list the procedure for carrying out a differential levelling exercise where one point

  A typical gas stove burner supplies a kettle filled

A typical gas stove burner supplies a kettle filled with water at a rate of 15,000 Btu/hr with a flame temperature of 750C

  The compressor is cooled by the ambient air at 15 degc at

air enters a compressor at ambient conditions of 100kpa and 17 degc with a low velocity and exits at 1mpa 327 degc and

  Choosing the helium to be your system determine the work

a cycle using helium in a piston-cylinder device starts at t1 300 k and p1 0.2 mpa. the helium is then compressed

  Suppose we want to cool a sample of n2 gas at room

for n2 gas cpm is nearly constant at 3.5r 29.1 jmol k for temperatures in the range 100 to 400 k and for low or

  Calculate the maximum power of the wind on each site in kw

two sites are being considered for wind power generation. on the first site the wind blows steadily at 7 ms for 3000

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd