A rigid insulated vessel is divided into two compartments

Assignment Help Mechanical Engineering
Reference no: EM13625373

A rigid, insulated vessel is divided into two compartments connected by a valve. Initially, one compartment, occupying one-third of the total volume, contains air at 500 degree Rankine, and the other is evacuated. The valve is opened and the air is allowed to fill the entire volume. Assuming the ideal gas model, determine the final temperature of the air, in degree Rankine, and the amount of entropy produced, in Btu/degree Rankine per lb of air.

Reference no: EM13625373

Questions Cloud

What is the distance h above the victims arm where the : a blood transfusion is being set up in an emergency room for an accident victim. blood has a density of 1060 kgm3 and a
Saturated liquid water at 1 kgs and 200 kpa is mixed : saturated liquid water at 1 kgs and 200 kpa is mixed steadily with 4 kgs of water at 200 kpa and 200ordmc with the goal
Calculate the moment mn-m on the door hinge post on line : a ship channel has a depth of 16 m and an upper width of 16 m. the sides of the channel are curved such that the width
Use exponential smoothing with alpha 2 and the smoothed : the following data summarizes the historical demand for a productmonthactual
A rigid insulated vessel is divided into two compartments : a rigid insulated vessel is divided into two compartments connected by a valve. initially one compartment occupying
What would the mole and mass fractions be if she was to : a combustion engineer wishes to produce an inert mixture to replace normal air. she will do that using a mixture of n2
Water flows at 50oc inside a 25-cm-inside-diameter tube : 1.water flows at 50oc inside a 2.5-cm-inside-diameter tube such that hi 3500 wm2 oc. the tube has a wall thickness of
She knows that a high wind reduces the air pressure on the : dorothy is up on her 11.0m by 14.0m roof enjoying the view of kansas. suddenly a strong wind blows down her ladder
Assuming the process is adiabatic is this process possible : a vortex tube is used to separate an ideal gas at 10 bar and 375 k such that half the gas is collected in a cool stream

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Consider a concentric tube annulus for which the inner and

consider a concentric tube annulus for which the inner and outer diameter are 25 and 50 mm. water enters the annular

  Two carts a and b are moving in a straight line with

two carts a and b are moving in a straight line with velocities v and 2v respectively. the length of each of the carts

  Explain why the two measurements give different values

A similar measurement is made applying the force parallel to one of the cube axes. Explain why the two measurements give different values of the elastic modulus.

  Determine the power requirement w and volumetric flow rate

a refrigerator uses a compressor that employs r-134a as the refrigerant. determine the power requirement w and

  A person of weight 100 kg standing on skis 2 m long and 010

question 1 it is observed that snow lies stably on roofs with a slope of less than 24deg but that it slides off roofs

  Determine the minimum no of teeth required on pinion in

determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to

  What are the properties of petrol

what are the properties of petrol that it make particularly suitable for the use as fuel in a motor vehicle.

  What dielectric constant must the material between the plate

A simple plate capacitor can store 6.5x10^-5 C at a potential of 10000 V. what dielectric constant must the material between the plates have if their area is 6.0x10^-5 m2 and they are 0.16 mm apart?

  Find the velocity of the wind

A plane can fly 299 mph in still air. If it can fly 180 miles downwind in the same amount of time it can fly 119 miles upwind, find the velocity of the wind.

  Determine the linear coefficients of expansion

What was the percentage error found between experimental and accepted values and what caused any errors, and how could they be minimised?

  Te current density is 1000 am2 the voltage load is 62 of

determine the theoretical conversion efficiency for a methaneoxygen fuel cell that operates at a temperature of 500

  Determine the initial and final pressures

Friction between the piston and the cylinder wall can be neglected. For the air, determine the initial and final pressures, in kPa, and the work, in kJ.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd