A rigid container is separated into 2 compartments by a

Assignment Help Mechanical Engineering
Reference no: EM13622811

A rigid container is separated into 2 compartments by a very thin solid membrane. One side initially holds 2 m^3 of air at 27C and 0.3 MPa. The other side is initially evacuated and has volume of 3 m^3. At some point, due to transfer of 697 kJ of heat from the surrounding to the first compartment, air pressure increases and results in mechanical failure and opening of the membrane, allowing the air to occupy the full volume of the container.

Determine the following:

1. Draw the schematic and define the system used for analysis

2. Mass of the air (m=? in [kg])

3. The final temperature of the air after the membrane rupture (T2=? in [K])

4. The final pressure of the air after the membrane rupture (p2=? in [MPa])

5. Work performed by air on the surroundings outside the container (W12=? [kJ])

Reference no: EM13622811

Questions Cloud

A bank manager wishes to provide prompt service for : a bank manager wishes to provide prompt service for customers at the banks drive-up window. the bank currently can
Alabaster incorporated has an equtiy cost of capital of 14 : alabaster incorporated has an equtiy cost of capital of 14. the debt to value ratio is .6 the tax rate is 35 and the
The detectors on the rocket record the flashes from both : two guns a and b located at xa 0 and xb 1.5 km fire at an approaching rocket. gun a fires at t 0 gun b fires at t
Te table below shows lifetime peptic ulcer rates per 100 : the table below shows lifetime peptic ulcer rates per 100 population u for various family incomes x as reported by the
A rigid container is separated into 2 compartments by a : a rigid container is separated into 2 compartments by a very thin solid membrane. one side initially holds 2 m3 of air
A project requires buying a 30000 equipment which will be : a project requires buying a 30000 equipment which will be depreciated straight-line to zero over its 5-year life. the
Can the company maintain its current capital structure : world wide oil corporation is reviewing its capital budget for the upcoming year. it has paid a 3.00 dividend per
Lee corporation intends to purchase equipment for 1000000 : lee corporation intends to purchase equipment for 1000000. the equipment has a 5 year useful life and will be
Calculate the force produced by the cylinder for extension : a double-acting cylinder has a piston with a diameter of 25 mm. the piston rod is 5 mm in diameter and pressure is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd