A peripheral milling operation is performed on the top of a

Assignment Help Mechanical Engineering
Reference no: EM13645626

A peripheral milling operation is performed on the top of a rectangular workpiece that is 650 mm long, 50 mm wide, and 110 mm thick. The milling cutter has a diameter of 60 mm and five teeth, and overhangs the width of the workpiece on both sides. The cutting conditions are as follows: cutting speed is 55 m/min, chip load is 0.30 mm/tooth, and depth of cut is 9 mm. (a) Determine the time needed to make one pass across the surface, (b) the maximum material removal rate during the cut.

Reference no: EM13645626

Questions Cloud

Assuming the friction force is constant determine how much : a 7.80-g bullet moving at 480 ms penetrates a tree trunk to a depth of 6.5 cm.a use work and energy considerations to
What is the net work done on the particle by external : a 0.800-kg particle has a speed of 1.30 ms at point a and kinetic energy of 8.00 j at point b.a what is its kinetic
Formulate hypotheses that could be used to determine : according to the pew internet amp american life project 75 of american adults use the internet. the pew project authors
A raindrop of mass 30610e5 kg falls vertically at constant : a raindrop of mass 3.0610e5 kg falls vertically at constant speed under the influence of gravity and air resistance.
A peripheral milling operation is performed on the top of a : a peripheral milling operation is performed on the top of a rectangular workpiece that is 650 mm long 50 mm wide and
A skydiver of mass 830 kg jumps from a slow-moving aircraft : a skydiver of mass 83.0 kg jumps from a slow-moving aircraft and reaches a terminal speed of 54.9 ms.a what is her
The water is heated to 160degc at constant volume and is : a piston-cylinder assembly contains 5 kg of a two-phase liquid-vapor mixture of water having 32 quality is initially at
A 10-kg cylinder rolls without slipping on a rough surface : a 10-kg cylinder rolls without slipping on a rough surface. at an instant when its center of gravity has a speed of 10
A man weighing 750 n and a woman weighing 480 n have the : a a cardinal richmondena cardinalis of mass 4.00times10-2 kg and a baseball of mass 0.140 kg have the same kinetic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the heat transfer coeffcient due to natural

for this problem we will be analyzing a power amplier that is surrounded by air at 25c while the case which is

  A horizontal cantilever of length l supports a load w

a horizontal cantilever of length l supports a load w uniformly distributed along its length. the cantilever is proped

  Horizontal motion of the piston rod of the hydraulic

horizontal motion of the piston rod of the hydraulic cylinder in figure 7 controls the rotation of link ob about o. for

  A mass of 5kg of saturated liquid-vapor mixture of water is

a mass of 5kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 100 kpa. initially

  Determine the annual cost of the heat loss per square foot

a wall has a total r-value of 15. determine the annual cost of the heat loss per square foot in a climate having 5000

  Consider a house shown in fig 14-10 that contains air at

in cold weather condensation frequently occurs on the inner surfaces of the windows due to the lower air temperatures

  Air at 147 psia and 70 degrees farenheit is compressed

air at 14.7 psia and 70 degrees farenheit is compressed adiabatically by a centrifugal compressor to a pressure of 100

  An of milk at 68of is placed in a refrigerator

1 given amp find a r-134a at t 60oc and v 0.072 m3kg. find p and h.b ammonia at p 8 bar and v 0.005 m3kg. find

  Assume the cost of electricity is 89 cents per kwh

an electrically driven pump operating at steady state is used to draw water from a pond. at the pump inlet the pressure

  Determine the velocity and the acceleration of the slider

for the mechanism shown in fig 8.81 link 2 rotate at a constant angular velocity. determine the velocity and the

  A system executes a power cycle while receiving 1000 kj by

a system executes a power cycle while receiving 1000 kj by heat transfer at a temperature of 500 k ad discharging

  Draw a t-s diagram of the process through the cycle neglect

a gas refrigeration system composed of a turbine a compressor and two heat exchangers is operating at steady state. air

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd