A nozzle with inlet area of 800 cm2 and inlet steam

Assignment Help Mechanical Engineering
Reference no: EM13630867

A nozzle with inlet area of 800 cm2 and inlet steam velocity is 10m/s. The steam pressure is 800kPa and temperature is 400C at the inlet and the pressure and temperature change into 200kPa and 300°C at the outlet. The heat loss of the process is 25kW. Determine the exit velocity and volume flow rate if it is considered as a steady flow.

Reference no: EM13630867

Questions Cloud

100kpa and 22 degc air is contained in a rigid tank of 2 m3 : 100kpa and 22 degc air is contained in a rigid tank of 2 m3. there is supply line connected to the tank through a
A square plate of edge length 120 cm and negligible : a square plate of edge length 12.0 cm and negligible thickness has a total charge of 5.80 x 10-6 c. estimate the
More heat is transferred to the air until the temperature : five kilograms of air at 300 k is contained in a vertical cylinder by a frictionless piston of a mass such that the
A mixing chamber steadily mixes a hot water stream at : a mixing chamber steadily mixes a hot water stream at 80degc and 0.5kgs rate with a cold water stream at 20degc. if the
A nozzle with inlet area of 800 cm2 and inlet steam : a nozzle with inlet area of 800 cm2 and inlet steam velocity is 10ms. the steam pressure is 800kpa and temperature is
Using the classical and relativistic expressions for : using the classical and relativistic expressions for kinetic energy calculate the range of velocities for a particle of
Knowing that the constant of eachspring is 2 knm determine : a 10-kg block is attached to spring a and connected to spring b bycord and pulley. the block is held in the position
A heat pump with a cop of 30 is used to heat air contained : a heat pump with a cop of 3.0 is used to heat air contained in a 1205.4m3 of well-insulated rigid tank. initially the
It is now cooled at constant volume to 200 deg c this : a system with an initial volume of 2 m is filled with water at 3 mpa 400 deg c.it is now cooled at constant volume to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the vertical displacement

calculate the vertical displacement at D and the horizontal displacement at Free-Body Diagram should be recalculated with P and Q.

  What is the section lift coefficient

Consider a NACA 0009 airfoil that has a plain flap whose length is 0.2c and which is deflected 25. a. Calculate cl and cmc/4 When the geometric angle of attack is 4 degrees, what is the section lift coefficient? Where is the center of pressure?

  Air at a stagnation pressure of 450 kpa and stagnation temp

air at a stagnation pressure of 450 kpa and stagnation temp of 400k flows through a converging nozzle whose throat area

  Each turbine stage operates with an isentropic efficiency

water is the working fluid in a vapor power cycle with superheat and reheat. superheated vapor enters the first turbine

  Consider an iron-carbon alloy that contains 02 wt c in

consider an iron-carbon alloy that contains 0.2 wt c in which all the carbon atoms reside in tetrahedral interstitial

  What is the packing density

What is the packing density

  The allowable shear stress in the bolts is 10000 psi

a flanged coupling joins two pieces of 4-in diameter shaft. the .625 bolts are arranged in a single 8 diameter bolt

  Explain what is thermal efficiency and the moisture content

Each turbine stage isentropic efficiency of 85% FWH is open T-S diagram for cycle? What is thermal efficiency and the moisture content of the steam leaving the low-pressure turbine?

  Water at 70 kpa and 100 c is compressed isentropically in

water at 70 kpa and 100 c is compressed isentropically in a closed system to 5 mpa.determine the final temperature of

  A hot wire anemometer is a device to measure the velocity

a hot wire anemometer is a device to measure the velocity of a flow of air. it consists of a thin cylindrical wire in

  A wind tunnel is 6m long and has a cross section of 1m2 air

a wind tunnel is 6m long and has a cross section of 1m2. air flows through at 70ms at standard sea-level conditions

  Heat transfer to the water continues until its pressure is

a two-phase liquid-vapor mixture a two-phase liquid-vapor mixture of water with an initial quality of 25 is contained

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd