A new prototype proven to perform with an isp of 1000s but

Assignment Help Mechanical Engineering
Reference no: EM13619614

When deciding what propulsion system is most appropriate for a mission, thrust and Isp are not the only parameters that need to be considered. A mission planner must balance considerations of mission impact based on a combination of factors, including: mass benefit, complexity, heritage (or flight readiness), and risk ; all of which serve to provide a holistic assessment of a propulsion subsystem choice.

a) using the simplified rocket equation, plot the ratio of propellant of final mass for an Isp range of 100 to 1500s for a Single-Stage-to-Orbit (SSTO) launch vehicle. Use delta V = 9km/s. Based on this graph decide between a solid rocket motor (Isp = 250s) and a bipropellant liquid engine (Isp = 450s) . Justify your answer quantitatively and qualitatively

b) Do the same for a LEO to GEO transfer (delta V = 4km/s). A spacecraft has a thruster with an Isp of 800s. A new prototype, proven to perform with an Isp of 1000s, but which has never been flown, is being considered. Do the mass savings achieved by the new thruster justify its use? Justify your answer quantitatively and qualitatively.

Reference no: EM13619614

Questions Cloud

Two solenoidal coils a and b are wound using equal lengths : two solenoidal coils a and b are wound using equal lengths of the same kind of wire. the length of the axis of each
If someone is 19 years old deposits 3000 each year into a : if someone is 19 years old deposits 3000 each year into a traditional ira individual retirement account for 51 years at
Measurement indicates that to cause this flow the acting on : a fluid flow steadily in the x direction through a control volume. measurement indicates that to cause this flow the
The magnetic field inside a superconducting solenoid : the magnetic field inside a superconducting solenoid is5.50t. the solenoid has an inner diameter of 6.20 cm and a
A new prototype proven to perform with an isp of 1000s but : when deciding what propulsion system is most appropriate for a mission thrust and isp are not the only parameters that
Your company is considering a new project that will require : your company is considering a new project that will require 250000 of new equipment at the start of the project. the
A dock worker applies a constant horizontal force of 770 : a dock worker applies a constant horizontal force of 77.0 to a block of ice on a smooth horizontal floor. the
A loxlh2 rocket engine with a chamber pressure of 25 atm is : a loxlh2 rocket engine with a chamber pressure of 25 atm is optimized with an isentropic nozzle that is perfectly
Estimate the power required to operate the luggage conveyor : a luggage conveyor belt is inclined at at an angle 14.8 degrees and has length 330m. the belt moves at a speed of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd