A natural gas engine has a bsfc of 9000 btushp-hour when

Assignment Help Mechanical Engineering
Reference no: EM13625513

1. A natural gas engine has a BSFC of 9000 BTU's/hp-hour when producing 200 horsepower. How many BTU's per hour does the engine consume?

2. How many therms does the engine in problem 1 consume per hour?

3. If natural gas costs $0.35/therm, what is the natural gas cost to operate the engine in problem 2 per hour?

Reference no: EM13625513

Questions Cloud

Below are three sets of expected frequencies for the four : below are three sets of expected frequencies for the four cells of 2 x 2 contingency tables.identify which statistical
For the compressor the isentropic efficiency is 92 and for : air enters the compressor of a regenerative air-standard brayton cycle with a volumetric flow rate of 60 m3s at 0.8 bar
Using alpha 005 test whether or not there is a significant : during the recent primary elections the democratic presidential candidate showed the following pre-election voter
A first-order system is subjected to a harmonic input of : a first-order system is subjected to a harmonic input of 3hz. the system has a time constant of 0.5s. calculate the
A natural gas engine has a bsfc of 9000 btushp-hour when : 1. a natural gas engine has a bsfc of 9000 btushp-hour when producing 200 horsepower. how many btus per hour does the
The following data presents test scores on a behavioral : the following data presents test scores on a behavioral vignettes test for self-help skill teaching for the primary
An asteroid orbits the sun at a constant distance of : an asteroid orbits the sun at a constant distance of 4.350e11 meters. the suns mass is 1.99times1030 kg. what is the
The yield stresses of several samples of a steel containing : the yield stresses of several samples of a steel containing 0.12 carbon with different grain sizes were measured. the
A radio wave transmits 143 wm2 of power per unit area a : a radio wave transmits 14.3 wm2 of power per unit area. a flat surface of area a is perpendicular to the direction of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 3 m x 3 m x 24 m room losses heat through the walls at a

a 3 m x 3 m x 2.4 m room losses heat through the walls at a rate of 520 w. determine the final temperature of the room

  Two kg of a mixture having an analyis of on a mass basis of

two kg of a mixture having an analyis of on a mass basis of 30 nitrogen 40 carbon dioxide 30 oxygen is compressed

  If the sprinkler at a is 1 m from the ground then scale the

if the sprinkler at a is 1 m from the ground then scale the necessary measurements from the photo to determine the

  Calculate the ratio of the initial to final speed of sound

Air expands isentropically from 1.5 MPa and 60 C (centigrade) to 0.4 Mpa. Calculate the ratio of the initial to final speed of sound.

  Compute the interplanar spacing for the set of planes

compute (a) the interplanar spacing for the set of planes and (b) the atomic radius for the rhodium atom.

  A turbine is operated with an enthalpy at entrance of 1340

a turbine is operated with an enthalpy at entrance of 1340 btulbm and an exit enthalpy of 1285 btulbm. if the entrance

  The radial loads of both gears are in the same plane and

a shaft is to be designed to support the spur pinion and helical gear shown in the figure on two bearings spaced 700 mm

  When theta reaches 60 degrees the links have an angular

the parallelogram linkage shown moves in the vertical plane with the uniform 8-kg bar ef attached to the plate at e by

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  The hole must have a diameter of b 25 mm determine the

the aluminum plate of thickness t 3.5 mm. is to be designed so the maximum stress remains below 100 mpa. the hole must

  Two 10 inch gears are to be mounted 12 inches apart and

two 10 inch gears are to be mounted 12 inches apart and have a velocity ratio of 51. find the pitch diameters and the

  Consider a plate with uniform heat generation q for k200

consider a plate with uniform heat generation q. for k200 wmk q40 mwm3. t1160 c at x0 t2100 c at x2l and a plate

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd