A multiple variable digital control

Assignment Help Electrical Engineering
Reference no: EM131393072

A multiple-variable digital control uses a reaction vessel for which binary inputs of level, temperature, and pressure drive binary outputs to the input valve and the output valve.

A digital HIGH opens a valve. The following conditions must be satisfied:

Pressure

Temperature

Level

Input Valve

Output Valve

H

H

H

L

H

L

H

H

L

H

L

H

L

L

L

L

L

L

H

L

H

L

L

H

H

H

L

H

L

L

Reference no: EM131393072

Questions Cloud

Find the maximum sampling rate for a line : It requires 14 instructions at /instruction for the computer to address and process one line of data. The multiplexer switching time is , and the ADC conversion time is. Find the maximum sampling rate for a line.
What is the maximum signal acquisition : A data-logging system must take samples of 40 variables at 100 samples per second each. What is the maximum signal-acquisition and processing time in microseconds?
Senior citizen discounts : Which of the following is a plausible reason that restaurants offer "Senior Citizen Discounts"? Two countries, A and B are identical except that the depreciation rate of capital is much higher in A. Both economies have no growth.
What can you imply about yourself from the given comparison : Describe your thought process while performing your SWOT analysis. What can you imply about yourself from this comparison? How does it compare to other students' thought processes?
A multiple variable digital control : A multiple-variable digital control uses a reaction vessel for which binary inputs of level, temperature, and pressure drive binary outputs to the input valve and the output valve.
Find the input angles corresponding to the toggle positions : Find the input angles corresponding to the toggle positions of the non-Grashof linkages in Table P4-1. (For this problem, ignore the values of θ2 given in the table.)
What is role of it and e-commerce in serving your customers : What is the role of information technology and e-commerce in serving your customers? What are the key performance measures for evaluating your supply chain?
Make use of the idea of debt measured as fraction : The editor of the Financial Times hires you to write a short article explaining why the US government’s debt is higher than its ever been in history. Either take the view that the debt is a serious problem that needs to be addressed or argue that it ..
Discuss the objective of resume and develop objective : Discuss the “objective” of a resume, and develop an objective statement for a position you seek, or, expect to seek when you complete your education and training. Suppose $1 = 10.5 pesos in New York and $1 = 9.6 Pesos in Mexico City. If you had $10,0..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Plot the potential with respect to position

Potential due to point charge and spherical charge distribution. A point charge Q is surrounded by a uniform spherical charge distribution of radius a, having a uniform volume charge density pv.

  Design each of the circuits specified in procedure section

Design each of the circuits specified in the Procedure section of this lab. Your design should attempt to get within § 5 % of the specified gain. All designs are to use standardcommercial 5 % resistors. You may only use a single resistor for each ..

  Find the rms current the motor draws from the supply

A small ac motor, draws 100 VA from its 120-Vrms, 60 Hz ac source and consumes 50 W. Find the rms current the motor draws from the supply.

  Design an iir band stop butterworth filter

Design an IIR BAND STOP Butterworth filter with the following characteristic

  How the signals were changed to a power level

A typical method of measuring the linearity of an amplifier is called the "Two-tone" test. Signals at f1 and f2 are input to the amplifier and the output spectrum is observed. Assuming that signals at 14.1 and 14.2 MHz are input to an amplifier.

  What is the maximum negative voltage at the output of cicuit

Due to its wider bandgap than silicon, a GaAs red light emitting diode (LED) typically has a turn-on voltage of 1.6 V. Assuming the maximum allowable current through the LED is 16.7 mA,

  Find the change in currents due to change of voltage

1. Find the change in currents due to change of voltage by (a) 5mv,(b) -10mv, (c) 15mv using small signal model and exponential modelof diode with n= 1 and biased at 2mA. 2. A step up transformer has the turn ratio of 2:5

  What is voltage required to get classical music station

The p-n junction in part (a) is used as a capacitor in an LC circuit to tune two WHRO stations in your car radio. When no voltage is applied a radio station transmitting at 89.5 MHz is received. What is the voltage required to get the classical mu..

  What is the resonant frequency of the circuit

What would be the resonant frequency if the inductor resistance were reduced to 40 Ω?

  Determine magnitude of line to-line voltage at load terminal

A balanced delta connected load of 15 + j18 ohms per phase is connected at the end of a three-phase line. The line impedance is 1 + j2 ohms per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 V rms.

  Estimate the heat effect per mole of hcl neutralized

Estimate the heat effect per mole of HCl neutralized if the tank is maintained at 298.15 K (25°C) and 1 atm and the neutralization reaction goes to completion.

  Calculate the annual saving effected

If the power factor is improved to 0·9 lagging by means of loss-free capacitors costing Rs 60 per kVAR, calculate the annual saving effected.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd