A mass of 55 kg is suspended from a spring of stiffness 835

Assignment Help Mechanical Engineering
Reference no: EM13632735

A mass of 55 kg is suspended from a spring of stiffness 83.5 kg/cm. A dash pot is fitted and it is found that the amplitude of the vibration diminishes to 1/5 of its original value after 2 complete vibrations.

i) Find
a) the value of the damping force,

b) the frequency of vibration.

ii) Compare it with the frequency of the free vibration

Reference no: EM13632735

Questions Cloud

The combined mass is shot horizontally off the cliff with : the following takes place at a colony on the moon some time in the distant futurea 40 kg cannon is loaded with a 10 kg
Sketch mohrs circle for this state of stress and determine : the principal stresses at a given point are sigma1 10 mpa sigma2 ?100 mpa. sketch mohrs circle for this state of
An engine of mass 180 kg is to be supported on four helical : an engine of mass 180 kg is to be supported on four helical springs. when the engine speed is 900 rpm there is a
A research engineer for a tire manufacturer is : a research engineer for a tire manufacturer is investigating tire life for a new rubber compound and has built 16 tires
A mass of 55 kg is suspended from a spring of stiffness 835 : a mass of 55 kg is suspended from a spring of stiffness 83.5 kgcm. a dash pot is fitted and it is found that the
Calculate the ratio of the etched and original crack tip : the fracture strength of glass may be increased by etching away a thin surface layer. it is believed that the etching
The shear stresses on planes perpendicular to the y-axis : an element of a material experiences stresses sigmaz ?20 mpa sigmax 40 mpa tauexz 40 mpa sigmay 80mpa. the shear
Find a the temperature of the gas and b the average kinetic : a 7.00-l vessel contains 3.50 moles of gas at a pressure of 1.60x106 pa. find a the temperature of the gas and b the
The meat department of a supermarket sells ground beef in : the meat department of a supermarket sells ground beef in approximate 1 lb packages but there is some variability. a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the critical crack tip radius for a ceramic

calculate the critical crack tip radius for a ceramic material that has a flexural strength of 638 mpa an elastic

  Calculate the static thrusts of the rocket and turbojet

calculate the static thrusts of the rocket and turbojet engine described in the figure. the thrust t is the force

  The pipe undergoes a 90 degree bend and exits out a

a pipe transports water in a 4-cm-diameter pipe with an average velocity of 10 ms. the pipe undergoes a 90 degree bend

  If a football is kicked at a 45 degree angle determine its

if a football is kicked at a 45 degree angle determine its minimum initial speed va so that it passes over the goal

  Find sketch the process on a t-s diagram and a p-v diagram

an air otto cycle has compression ratio of 8. at the beginning or the compression process pressure is 1 bar.

  At the nozzle exit the pressure is 147lbfin2 and the

steam enters a well insulated nozzle operating at steady state at 1000of and 500lbfin2 and velocity 10fts. at the

  Sketch the thermal circuit of the system

Sketch the thermal circuit of the system. Label (using the above symbols) all pertinent nodes and resistances.

  What is the magnitude of the impulse applied to the

what is the magnitude of the impulse applied to the projectile by its weight from t 0 s to 3 s? given mass of

  The breaking strength x kg of a certain type of plastic

the breaking strength x kg of a certain type of plastic block is normally distributed with a mean of 1500 kg and a

  A boat and trailer are being pulled along a bumpy road at a

a boat and trailer are being pulled along a bumpy road at a velocity v. the contour of the road can be approximated by

  The circumfernce of the tire is 275 and the interia is

a car tire starts at rest and reaches a speed of 100 inches per minute and accomplishes this in 0.75 seconds. the

  Determine the required thickness of the insulation

If the pipe is to be insulated with glass wool insulation (k=.05 W/m C) in order to decrease the temperature rise of water to .25 degrees C, determine the required thickness of the insulation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd