A mass of 12kg of refrigerant-134a initially exists as a

Assignment Help Mechanical Engineering
Reference no: EM13630953

A mass of 12kg of refrigerant-134a initially exists as a saturated vapor in a piston-cylinder device at 240 kPa. Then, 300kJ of heat is transfered to the refrigerant at a constant pressure while a 110-V source supplies 12.8 amps of current to a resistor within the cylnider for 6 minutes.

Determine the following:

a. The work provided by the electrical source

b. Specific enthalpy at the final state

c. Temperature of the initial state.

d. Description of the final state.

e. Temperature of the final state.

f. Show the process on a P-v diagram with respect to saturation lines.

g. Compute the boundry work.

Reference no: EM13630953

Questions Cloud

The magnetic field inside a superconducting solenoid is : the magnetic field inside a superconducting solenoid is 5.00 t. the solenoid has an inner diameter of 6.20 cm and a
An engineer needs to monitor a flow of 20degc gasoline at : an engineer needs to monitor a flow of 20degc gasoline at about 250plusmn25 galmin through a 4- in-diameter smooth
Wat types of engineers eg civil construction mechanical : 1. what types of engineers e.g. civil construction mechanical industrial material science electrical etc. do you think
If the solenoid is connected in series with a 250nbspomega : a 494-turn solenoid has a radius of 7.95 mm and an overall length of 12.4 cm.a what is its inductance?b if the solenoid
A mass of 12kg of refrigerant-134a initially exists as a : a mass of 12kg of refrigerant-134a initially exists as a saturated vapor in a piston-cylinder device at 240 kpa. then
Air initially at rest m1 0 with an initial pressure p1 1 : air initially at rest m1 0 with an initial pressure p1 1 atm and temperature t1 300k flows through a nozzle into a
In boulder dam 2000 cubic feet per second of water flows : in boulder dam 2000 cubic feet per second of water flows through each of the pipes called penstocks that lead down to
What was the work transfer was the work done on or done by : 2kg of an ideal argon gas has been compressed irreversibly from an equilibrium state 1 where p1 2bar and v1 3m3 to an
In boulder dam 2000 cubic feet per second of water flows : in boulder dam 2000 cubic feet per second of water flows through each of the pipes called penstocks that lead down to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A carnot engine operates between temperatures of 700 and

a carnot engine operates between temperatures of 700 and 369 k. to improve the efficiency of the engine it is decided

  Draw a schematic of the turbine as a control volume label

steam having pressure 4.0 mpa and temperature of 880 k enters the turbine installed in a power plant at the rate 500

  Describe the principle and operation of an hearth furnace

Describe the principle and operation of an hearth furnace. Possible references: Making and Shaping of Steels by the American Society of Metals and Google resources.

  You are trying to loosen a bolt from a piece of metal with

you are trying to loosen a bolt from a piece of metal with a wrench but fail. what kind of wrench should you look

  Determine a the maximum temperature in the cycle the net

a four-cylinder four-stroke 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression

  The center lines of hte inlet and discharge pipes are at

a turbine is supplied with 0.6m3s of water from a 0.3m diameter pipe the discharge pipe has a diameter of 0.4m. the

  If the compressor consumes 400 w of power and the cop the

refrigerant-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at

  The wall system is 6m wide by 28m high what is the rate

a wall constructed of three layers is to be considered. the inner surface of the wall is maintained at 23 c and the

  If the temperature of the environment were 33o c what rate

most of the energy we consume as food is converted to thermal energy in the process of performing all our bodily

  Using constant specific heat method

Using constant specific heat method

  The automobile has a speed of 80 fts at point a and

the automobile has a speed of 80 fts at point a and anacceleration a having a magnitude of 10fts2 acting in the

  Calculate the engineering strain and the true strain for

a solid cylindrical specimen 200-mm high is compressed to a final height of 60 mm in two steps between frictionless

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd