A loxlh2 rocket engine with a chamber pressure of 25 atm is

Assignment Help Mechanical Engineering
Reference no: EM13619611

A LOX/LH2 rocket engine with a chamber pressure of 25 atm is optimized with an isentropic nozzle that is perfectly expanded at ground with a thrat area of 0.065 m^2. The fuel and oxidizer is fed into the non-calorically perfect combustion chamber with a stoichiometric mixture ratio at 250 K. You may assume that O2 and H2 do not dissociate, gamma for the products is 1.2, and that the specific heat curve fits are still valid beyond its range. Hint: the specific gas constant is a function of the degree of reaction found using chemical equilibrium.

a) Find the Isp and thrust produced by the rocket engine.

b) Discus qualitatively how the following values will be affected under the following conditions:

1) The thrust, assuming the nozzle is not calorically perfect

2) The flame temperature, assuming O2 and H2 dissociates

3) The mass flow rate, if operating at a higher altitude

4) The exit velocity, if using a fuel rich mixture.

Reference no: EM13619611

Questions Cloud

The magnetic field inside a superconducting solenoid : the magnetic field inside a superconducting solenoid is5.50t. the solenoid has an inner diameter of 6.20 cm and a
A new prototype proven to perform with an isp of 1000s but : when deciding what propulsion system is most appropriate for a mission thrust and isp are not the only parameters that
Your company is considering a new project that will require : your company is considering a new project that will require 250000 of new equipment at the start of the project. the
A dock worker applies a constant horizontal force of 770 : a dock worker applies a constant horizontal force of 77.0 to a block of ice on a smooth horizontal floor. the
A loxlh2 rocket engine with a chamber pressure of 25 atm is : a loxlh2 rocket engine with a chamber pressure of 25 atm is optimized with an isentropic nozzle that is perfectly
Estimate the power required to operate the luggage conveyor : a luggage conveyor belt is inclined at at an angle 14.8 degrees and has length 330m. the belt moves at a speed of
For a relaxed normal eye assume a viewing distance of 250 : a microscope has a 2.40-cm focal length eyepiece and a 0.810-cm objective lens. for a relaxed normal eye assume a
You are scheduled to receive a 500 cash flow in one year a : you are scheduled to receive a 500 cash flow in one year a 800 cash flow in two years and pay a 400 payment in three
Using the p value method test if vitamin c reduces the : twenty-two volunteers at a cold research institute caught a cold after having been exposed to various cold viruses. a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd