A long bar of rectangular cross section 04 m x 06 m on a

Assignment Help Mechanical Engineering
Reference no: EM13625043

A long bar of rectangular cross section, 0.4 m x 0.6 m on a side and having a thermal conductivity of 1.5 W/m x K, is subjected to the boundary conditions shown below. Two of the sides are maintained at a uniform temperature of 200 C. One of the sides is adiabatic, and the remaining side is subjected to a convection process with ambient temperature (T-amb) =30 C and h = 50 W/m^2 x K. Using an appropriate numerical technique with a grid spacing of 0.1 m, determine the temperature distribution in the bar and the heat transfer rate between the bar and the fluid per unit length of the bar.

Reference no: EM13625043

Questions Cloud

If the motorcycle travels over the crest at half speed : a motorcycle is traveling up one side of the hill and down the other side. the crest of the hill is a circular arc with
A centrifuge is used to remove solids from a 140 ppg mud : a centrifuge is used to remove solids from a 14.0 ppg mud using 8.33 ppg water. the mud and water enter the centrifuge
A pair of dice is rolled 270 times using the normal curve : a pair of dice is rolled 270 times. using the normal curve approximation what is the probability that a total of 7
Determine the pressure in bars and the enthalpy in kjkg at : a piston cylinder device having an initial volume of 2 m3 initially contains steam at 10 bars and 200oc state 1. the
A long bar of rectangular cross section 04 m x 06 m on a : a long bar of rectangular cross section 0.4 m x 0.6 m on a side and having a thermal conductivity of 1.5 wm x k is
When a 45 n force is applied tangentially to the disk : a solid cylindrical disk has a radius of 0.25 m and it can rotate about a vertical axis.a. when a 45 n force is applied
The inside temperature of the firebrick layer was measured : calculate the rate of heat loss through the vertical walls of a boiler furnace 4m by 3m by 3m high.the walls are
The motion of the electron can be seen as a circular : if we have an electron orbiting an atomic nucleus. we may think the electron is doing a circular motion around the
Calculate the velocity component at the point 2 05 0 : a velocity field is specified as v ax2i bxyj where a 2 m-1s-1 b -4 m-1s-1 and the coordinates are measured in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd