A late-model hummer has a frontal profile area of 31 m2 and

Assignment Help Mechanical Engineering
Reference no: EM13626688

A late-model Hummer has a frontal profile area of 3.1 m2 and a CD of 0.47. It is moving at a steady speed of 75 mph. a) If we ignore bearing friction, rolling resistance and "Johnny Law", how much power (in English units of hp) is needed at the wheels on level ground? b) If the engine/drivetrain efficiency (from fuel to the driving wheels) is 34 %, and the heating value of the gas is 44.5 MJ/kg, how much gas will we be using in gallons/hour?

Reference no: EM13626688

Questions Cloud

Find the equal annual payment series that would be : find the equal annual payment series that would be equivalent to the following increasing series of payments if the
Two large parallel metal plates carry opposite of equal : two large parallel metal plates carry opposite of equal magnitude. they are separated by 45.00 mm and the potencial
025 kg of red-hot 700 c coals are taken from the fireplace : 0.25 kg of red-hot 700 c coals are taken from the fireplace and left in the middle of a room. the room is 3 m x 4 m x
The blade is bolted to a bracket attached to the motor : a mechanic is reinstalling a newly-sharpened blade on a lawn mower. a wedged-in block of wood at c prevents the blade
A late-model hummer has a frontal profile area of 31 m2 and : a late-model hummer has a frontal profile area of 3.1 m2 and a cd of 0.47. it is moving at a steady speed of 75 mph. a
As the cord unravels from the wheels inner hub the angular : as the cord unravels from the wheels inner hub the angular velocity of the outer hub 2 rads. determine the magnitudes
Suppose that we have ratings of a restaurant from a sample : question 1suppose that we have ratings of a restaurant from a sample of 72 customers. each of the ratings is either
Give your answer using the theoretical efficacy of the pill : pharmaceutical companies advertise for the birth control pill an annual efficacy of 99.1 in preventing pregnancy.
Find the following a the final volume and the mass of the : one end of a tube is closed and the other is open. a 15 g projectile is placed near the closed end is fastened in place

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A ball of diameter 005 m and specific gravity 05 is dropped

a ball of diameter 0.05 m and specific gravity 0.5 is dropped from a height of 1 m into a large pool of water.

  Determine a the temperature of the refrigerant exiting the

refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady

  A long cylinder having a diameter of 90mm is placed in the

air at 101.3 kpa absolute and 25 c is flowing at a velocity of 10 ms in a wind tunnel. a long cylinder having a

  Compute the cross-sectional area in both square inches and

a base for a building column measures 18.0 in by 18.0 in on a side and 12.0 in high. compute the cross-sectional area

  If money is worth 6 compounded annually to you then you

if money is worth 6 compounded annually to you then you should prefer to receive 1750 per year for 5 years than to

  Find the magnitdue of the acceleration when it reaches

a sled is traveling down a curve which can be approxmiated by a parabola y .01x2. find the magnitdue of the

  A piston-cylinder initially contains 252 kg saturated

a piston-cylinder initially contains 2.52 kg saturated liquid water at 200 degrees celcius. now heat is transferred to

  What is the length of the slope of the ramp

Using the knon height and calculated base lenghth, what is the length of the slope of the ramp.

  Problem a 5x5 plate with a crack size of 2a15 is under a

problem a 5x5 plate with a crack size of 2a1.5 is under a spectrum load as shown below. the plate has a yield strength

  To what temperature should the r-22 be heated to lift the

r-22 in a pistoncylinder has mass 1 kg and temp. 10degc with a volume of0.02 m3 . initially state 1 the piston rests on

  Determine the torque that can be applied to a solid shaft

determine the torque that can be applied to a solid shaft of 20-mm diameter without exceeding an allowable shearing

  An electric motor has a rotor with a mass moment of

an electric motor has a rotor with a mass moment of inertia of 30 ft-lb-s2. what torque is required to accelerate it

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd