A large vessel had experienced an internal leak of a

Assignment Help Mechanical Engineering
Reference no: EM13344632

A large vessel had experienced an internal leak of a coolant. It was Friday and the work crew needed to get the vessel dried out to allow maintenance to be performed on Monday. Using C-clamps, they attached thick steel plates to the two vessel openings (one on each end) and attached a shop airline to one top of the plates. On the other, they drilled a ¼ inch diameter hole to allow the air to escape. They cracked the valve and left for the weekend. Answer the following questions: 
a. What are the possible outcomes of this scenario? 
b. What safety device(s) should have been used and "

Reference no: EM13344632

Questions Cloud

Block a and b weigh 100 lb and 60 lb respectively if block : block a and b weigh 100 lb and 60 lb respectively. if block a has a center of gravity at g as shown determine the
Signal-power absorbtion by a collection of atoms where : signal-power absorbtion by a collection of atoms where does the absorbed power go? consider the net steady-state
A total of 200 of a compound is allowed to react with water : a total of 2.00 of a compound is allowed to react with water in a foam coffee cup and the reaction produces 193 of
What fraction of a remains in the aqueous phase a if one : solute a has a partition coefficient of 3 between toluene and water with 3 times as much in the toluene phase. suppose
A large vessel had experienced an internal leak of a : a large vessel had experienced an internal leak of a coolant. it was friday and the work crew needed to get the vessel
A solution of sulphide ct10-6m is blended into a 04m : a solution of sulphide ct10-6m is blended into a 0.4m sodium chloride solution in a closed container. plot a pc-ph
For the waveform shown below obtain expressions for : 1. for the waveform shown below obtain expressions for fourier components for fundamental 5th 7th and 11th elements
How many grams of sodium lactate should be added to 100 of : how many grams of sodium lactate should be added to 1.00 of 0.150 lactic acid to form a buffer solution with 4.00?
Wat is the spectator ion for the chemical formula cl2 : what is the spectator ion for the chemical formula cl2 nabrbr2

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd