A horizontal force f pushes a 10 kg block up a

Assignment Help Mechanical Engineering
Reference no: EM13630011

A horizontal force F pushes a 10 kg block up a fricitionless ramp with a circular contour, the radius of curvature of the slop contour is 15 m . the force changes with time to maintain a constant velocity of 2 m/s up the ramp if the angle is 20 deg and g is 9,81 m/s^2

(a) Calculate the normal acceleration of the block.

(b) calculate the magnitude of the force at the instant where the angle is 20 deg.

Reference no: EM13630011

Questions Cloud

Define the physical uncontrolled seat including seat : a farm equipment manufacturer has a need to actively reduce the vibration of the operators seat using an electrodynamic
The dog starts running when the owners are d 80 m apart if : a dog runs back and forth between its two owners who are walking toward one another. the dog starts running when the
A tank fitted with an electrical resistor holds 2 kg of : a tank fitted with an electrical resistor holds 2 kg of nitrogen n2 initially at 1 bar. over a period of 10 minutes
A cheetah can accelerate from rest to 220 ms in 676 s a : a cheetah can accelerate from rest to 22.0 ms in 6.76 s.a assuming constant acceleration how far has the cheetah run in
A horizontal force f pushes a 10 kg block up a : a horizontal force f pushes a 10 kg block up a fricitionless ramp with a circular contour the radius of curvature of
Using a binomial table find the binomial probabilities px : using a binomial table find the binomial probabilities px associated with given n ratio and x. a. n6 ratio 0.10 p4 b.
Consider a cogeneration power plant modified with : consider a cogeneration power plant modified with regeneration. steam enters the turbine at 9 mpa and 400 c and expands
Refreigerant vapor exits at a pressure of 2 bar if the heat : refrigerant 134a flows at steady state throught a horizontal pipe having an inside diameter of 4 cm entering as
An uncharged capacitor and a resistor are connected in : an uncharged capacitor and a resistor are connected in series to a source of emf. if ? 4.68 v c 22.6 of and r 135

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Methane escapes through a small 10-7 m2 hole in a 10-m3

methane escapes through a small 10-7 m2 hole in a 10-m3 tank. the methane escapes so slowly that the temperature in the

  Convert the equation from part a so that the mass of oil in

a cylindrical storage tank with dimensions of 15 m height and 15 m inside diameter is used to store oil having a

  Air flows along a horizontal curve streamline with a curve

air flows along a horizontal curve streamline with a curve 20 ft raduis with a speed of 100fts. determine the pressure

  Explain the velocity of the ball when it reaches the highest

A ball with a mass of 0.25 kg is thrown vertically upward with an initial velocity of 10 m/s. What is the velocity of the ball when it reaches the highest point?

  The rod is in an air environment with tinfinity 20 degree

a brass rod 100 mm long and 5 mm in diameter extends horizontally from a casting at 200 degree c. the rod is in an air

  Problem 1a steel simple beam ab is supported by a copper

problem 1a steel simple beam ab is supported by a copper wire at the middle point c. the beam is subjected to a pair of

  The jib crane is supported by a pin a c and rod ab the rod

the jib crane is supported by a pin a c and rod ab. the rod can withstand a maximum tension of 40kn. if the load has a

  An alloy named cylon is composed of 25 wt of metal a and 75

an alloy named cylon is composed of 25 wt. of metal a and 75 wt. of metal b. if the densities of metals a and b are

  In a 150 mw steam turbine unit operating on an enhanced

in a 150 mw steam turbine unit operating on an enhanced rankine cycle steam is delivered from the boiler to the high

  A 200-kg 5-m-wide rectangular gate shown innbspthe figure

a 200-kg 5-m-wide rectangular gate shown innbspthe figure is hinged at b and leans against thenbspfloor at a making an

  Calculate the work required to compress air from standard

calculate the work required to compress air from standard atmosphereic pressure to 2.3 atm in kjkg air.a. assume a

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd