A horizontal force f pushes a 10 kg block up a

Assignment Help Mechanical Engineering
Reference no: EM13630003

A horizontal force F pushes a 10 kg block up a fricitionless ramp with a circular contour, the radius of curvature of the slop contour is 15 m . the force changes with time to maintain a constant velocity of 2 m/s up the ramp if the angle is 20 deg and g is 9,81 m/s^2

(a) Calculate the normal acceleration of the block.

(b) calculate the magnitude of the force at the instant where the angle is 20 deg.

Reference no: EM13630003

Questions Cloud

An uncharged capacitor and a resistor are connected in : an uncharged capacitor and a resistor are connected in series to a source of emf. if ? 4.68 v c 22.6 of and r 135
An ideal reheat rankine cycle with water as the working : an ideal reheat rankine cycle with water as the working fluid operates the inlet of the high-pressure turbine at 8000
An ideal reheat rankine cycle with water as the working : an ideal reheat rankine cycle with water as the working fluid operates the inlet of the high-pressure turbine at 8000
According to most estimates 10 of the people in the general : according to most estimates 10 of the people in the general population are left-handed and 90 are right-handed. a
A horizontal force f pushes a 10 kg block up a : a horizontal force f pushes a 10 kg block up a fricitionless ramp with a circular contour the radius of curvature of
According to most estimates 10 of the people in the general : according to most estimates 10 of the people in the general population are left-handed and 90 are right-handed. a
A recently negotiated union contract allows workers in a : a recently negotiated union contract allows workers in a shipping department 24 minutes for rest 10 minutes for
Studies find that in a random sample of 3000 adults aged 18 : studies find that in a random sample of 3000 adults aged 18 and over 1410 owned an mp3 player. the 95 large-sample
New york is roughly 3000 miles from seattle when it is 800 : new york is roughly 3000 miles from seattle. when it is 800 a.m. in seattle it is 1100 a.m. in new york. using this

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the final temperature and the work done during

air is compressed in a piston-cylinder device from 100 kpa and 17 c to 800 kp reversible adiabatic process. determine

  Determine temperature at which the water starts boiling

A cooking pot whose inner diameter is 20 cm is filled with water and covered with a 4-kg lid. If the local atmospheric pressure is 101 kPa, determine the temperature at which the water starts boiling when it is heated.

  Calculate the hourly gas flow rate for the conditions given

calculate the hourly gas flow rate for the conditions given as followsreadings differential pressure 50-in water static

  A 50-kg iron block and a 20-kg copper block both initially

a 50-kg iron block and a 20-kg copper block both initially at 80oc are dropped into a large lake at 15oc. thermal

  Estimate the design-stage uncertainty in determining the

estimate the design-stage uncertainty in determining the voltage drop across an electric heating element. the heater

  A viscous fluid flows past a flat plate such that the

a viscous fluid flows past a flat plate such that the boundary layer thickness of a distance d from the leading edge is

  Assuming the average fuel composition and energy content

u.s. energy use was approximately 100 quads quadrillions btu in 2008. about 85 of this energy was supplied by burning

  There are two pairs of saw horses or which untrimmed joists

during the construction of a house 6 joists of 24 feet each must be trimmed to the correct length of 23 feet. the

  Determine the pressure of the water

determine the pressure of the water after the partition has been remived and enough heat has been transferred so that the temperature of the water is 3(degrees)C.

  Air flows steadily through an adiabatic non-ideal turbine

air flows steadily through an adiabatic non-ideal turbine entering at 150 psia 900degf and 350 fts and leaving at 20

  Steam enters a nozzle at 30 bars and 320c and leaves at 15

steam enters a nozzle at 30 bars and 320c and leaves at 15 bars with a velocity of 535 ms. the mass flow rate is 8000

  Design value for the molded friction material and steel disk

Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd