A hollow cylinder made of copper has an outer diameter

Assignment Help Mechanical Engineering
Reference no: EM13701046

A hollow cylinder made of copper has an outer diameter of 200 mm, an inner diameter of 50 mm and a height of 100 mm. Under load P the final height of the cylinder is 60 mm and the inner diameter is 45 mm. If the strength coefficient K is 315 Mpa and the strain hardening exponent is 0.54, what is the amount of load P?

Reference no: EM13701046

Questions Cloud

Adiabatic flame temperature vary-increasing combustion air : Propane gas (C3H8) at 25C, 1 atm enters an insulated reactor operating at steady state and burns completely with air entering at 25C, 1atm. Plot the adiabatic flame temperature versus percent of theoretical air ranging from 100 to 400%. Why does the ..
What is the gauge pressure and absolute pressure : Atmospheric pressure is101.3 kPa (or else 14.69 psi). You take a vessel, and pressurise it to 350 kPa (or 50.75 psi) above the atmospheric pressure, and connect pressure gauges to the vessel, calculate What is the gauge pressure? What is the absolute..
What value would be displayed on the scada screen : A 4 20 mA signal is sent to a 12-bit Modicon PLC input card, which in turn, sends this to a SCADA. If the signal happens to be 14.25 mA, calculate: What percentage of 0 - 100% will this represent?
Cylinder device nitrogen gas executes a carnot power cycle : In a sealed piston cylinder device Nitrogen gas executes a CARNOT POWER CYCLE. The source and sink temperatures are 999 K and 333 K. Minimum pressure in the cycle is 20 kPa. The minimum volume is (1/40) of the maximum volume in the cycle. The cycle w..
A hollow cylinder made of copper has an outer diameter : A hollow cylinder made of copper has an outer diameter of 200 mm, an inner diameter of 50 mm and a height of 100 mm. Under load P the final height of the cylinder is 60 mm and the inner diameter is 45 mm. If the strength coefficient K is 315 Mpa and ..
Heat conduction experienced by the person to the ice : A person with a uniform temperature of 29 C is standing barefoot on a block of ice in a breezy room at 20 C with an effective convection coefficient equal to 8 W/m^2 C. The surface area exposed to forced convection is 1.6 m^2.
What is the temperature and humidity of the outlet stream : A stream of air at 1 bar, 20 °C, 30% RH, at 100 m3/min is mixed with a stream of hot moist air at 120 °C, 75% RH, at 20 m3/min. What is the temperature and humidity of the outlet stream?
How did cincinnati zoo benefit from business intelligence : How did the Cincinnati Zoo benefit from business intelligence and how did it enhance operational performance and decision making?
A rotor is being designed for a wind turbine : A rotor is being designed for a wind turbine. The rotor will have a diameter of D = 70 m. A single airfoil will be used for the length of the blades. The airfoil has its minimum drag to lift ratio when the lift coefficient is 1.0. Two options are bei..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd