A helical compression spring is made of no 18 0147 in wire

Assignment Help Mechanical Engineering
Reference no: EM13620051

A helical compression spring is made of No. 18 (.0147 in) wire having a torsional yield strength of 108 kpsi. It has an outside diameter of ½ in and has 14 active coils.

a. Find the maximum static load corresponding to the yield point.

b. What deflection would be caused by the load from (a) above.

c. Calculate the scale of the spring.

d. If the spring has one dead turn at each end, what is the solid height ?

e. What should be the length of the spring so that when it is compressed solid, the stress will not exceed the yield point?

Reference no: EM13620051

Questions Cloud

What is the spring rate of each what force is required to : two steel compression coil springs are to be nested. the outer spring as an inside diameter of 1.5 in a wire diameter
Abc co needs to acquire equipment at a cost of 2500000 : abc co needs to acquire equipment at a cost of 2500000 includes set up costs of 225000 deemed to be capitalized
A solenoid is made of 283 turns of wire wrapped around a : a solenoid is made of 283 turns of wire wrapped around a hollow cylinder of radius 1.30 cm and length 6.78 cm. what is
What is the distance between the hook ends if the spring is : a helical tension spring is made of 1.2 mm wire having a yield strengths of 1280 mpa tension and 740 mpa torsion. the
A helical compression spring is made of no 18 0147 in wire : a helical compression spring is made of no. 18 .0147 in wire having a torsional yield strength of 108 kpsi. it has an
Six years from now you will be inheriting 100000 what is : six years from now you will be inheriting 100000. what is this inheritance worth to you today if you can earn 6.5
Todd and cathy created a firm that is a separate legal : todd and cathy created a firm that is a separate legal entity and will share ownership of that firm on a 5050 basis.
An 10-kg ball moving at 22 ms collides elastically and : an 10-kg ball moving at 22 ms collides elastically and head-on with a second 6-kg ball moving in the opposite direction
Determine the heat transfer and the work in kj kg also : the initial temperature is t 162 c air expands as an ideal gas from 10 bar and the above temperature to 1 bar in an

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The time it takes for sound waves to travel at 343 ms

two astronauts are 1.2 m apart in their spaceship. one speaks to the other. the conversation is transmitted to earth

  It is desired to design a system to keep a 1-million-galon

it is desired to design a system to keep a 1-million-galon capacity water tank filled. the plan is to use a centrifugal

  Air within a piston-cylinder assembly initially at 12bar

air within a piston-cylinder assembly initially at 12bar 327 degree celcius undergoes an isentropic expansion to

  Calculate the work done by the gases assuming they can be

after a combustion process in a cylinder the pressure is 1200 kpa and the temperature is 350 c. the gases are expanded

  At the exit the pressure is 24 bar and the temperature is

air flows through a well-insulated nozzle operating at steady state. at the inlet the pressure is 5 bar the temperature

  Flywheelsthe aim of this demonstration is to become

flywheelsthe aim of this demonstration is to become familiar with the derivation of material indexes in general and for

  The coefficient of sliding friction is muk determine the

a uniform sphere is projected without rotation at speed v0 up an inclined plane the makes an angle theta with the

  What will be the charge on the capacitor a long time after

capacitor with capacitance 6.00 microf is connected to a resistor with r 780 o in series and an emf source of 25.0 v

  In an em wave traveling north the e field oscillates

question in an em wave traveling north the e field oscillates vertically and has a frequency of 85.0 khz and an rms

  Determine the instantaneous center of rotation

determine (a) the instantaneous center of rotation of the double pulley (b) the velocity of th slider block (c) the number of inches of cord wrapped or unwrapped on each pulley per second.

  Determine the flight angle that maximizes the flow rate

The die characteristic is Q_x = 0.0015p where p is the head pressure in psi. Determine the flight angle that maximizes the flow rate Q_x and graph it.

  Use potential flow theory to determine the lift coefficient

use potential flow theory to determine the lift coefficient of a spinning baseball in terms of the forward velocity v

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd