A glass or epoxy laminate with a fiber orientation

Assignment Help Mechanical Engineering
Reference no: EM13138035

Question about Mechanics of composite materials
1. A glass/epoxy laminate with a fiber orientation of 30 degrees is subjected to a shear stress t_xy (or tau_xy) which can be positive or negative.

a) Determine the maximum positive and negative shear stresses that can be applied to the laminate using Tsai-Hill failure criterion.
b) Determine the reserve factors for t_xy = + 10 MPa and for t_xy = - 10 MPa. Note that the reserve factor is given by R = 1/Fl.

DATA: Ultimate strength values for glass/epoxy are:

sigma hat_1T = 1000 MPa
sigma hat_2T = 40 MPa
tau hat_12 = 80 MPa
sigma hat_1C = -800 MPa
sigma hat_2C = - 120 MPa

FORMULAE: Tsai-Hill failure criterion is given by:

Fl = [(sigma_1)/(sigma hat_1)]^2 - (sigma_1 * (sigma_2)/(sigma hat_1)^2 + [(sigma_2)/(sigma hat_2)]^2 + [(t_12)/(t hat_12)]^2 <= 1,

where sigma hat indicates the ultimate strength value given in the data.

2. Compute the burst pressure of a carbon/epoxy cylindrical vessel with a diameter of d = 250 mm and a wall thickness of t = 2.5 mm by:
a) Using the Tsai-Hill criterion
b) Using the maximum stress criterion

The cylindrical section of the pressure vessel is constructed by winding fibers in the circumferential direction

Data: Ultimate strength values for carbon/epoxy are:

sigma hat_1T = 1826 MPa
sigma hat_2T = 19 MPa
tau hat_12 = 75 MPa
sigma hat_1C = -1134 MPa
sigma hat_2C = - 131 MPa

Formulae: For cylindrical pressure vessels:
Circumferential stresses: sigma_c = pd /2t (16)
Axial stresses: sigma_a = pd /4t (17)

Tsai-Hill failure criterion is given by:

Fl^2 = [(sigma_1)/(sigma hat_1)]^2 - (sigma_1)(sigma_2)/(sigma_ hat_1)^2 + [(sigma_2)/(sigma hat_2)]^2 + [(tau_12)/(tau hat_12)]^2 <= 1.

where sigma hat indicates the ultimate strength value given in the data.

Maximum stress criteria are given by:

sigma_1 <= sigma hat_1
sigma_2 <= sigma hat_2
t_12 <= t hat_12

Reference no: EM13138035

Questions Cloud

What is the limiting reagent : How many grams of Cu(OH)2 can be produced from the reaction of 0.500g Cu with 30.0 mL of 3.0M NaOH? what is the limiting reagent?
Determining capital account increase : Franco and Jason share income and losses in a 2:1 ratio after allowing for salaries to Franco of $15,000 and $30,000 to Jason. If the partnership suffers a $15,000 loss, by how much would Jason's capital account increase?
Discussing the unified court system : The principle objective of a unified court system is to shift judicial administration from local control to centralized management, why would this be important?
How many moles of mgcl2 are present : How many moles of MgCl2 are present in 50.0 mL of 0.800 M MgCl2 solution?
A glass or epoxy laminate with a fiber orientation : A glass/epoxy laminate with a fiber orientation of 30 degrees is subjected to a shear stress t_xy (or tau_xy) which can be positive or negative.
The treasury auditors : The Treasury Auditors are currently exposed to unlimited liability for professional default. Auditors, and other professional groups have traditionally dealt with their unlimited liability exposure for professional default through professional indemn..
What is the molality of a solution : What is the molality of a solution prepared by dissolving 10.0 grams of methylamine, CH3NH2, in 50.0 mL of ethanol, C2H5OH?
What amount be reported for patent amortization expense : ELO feels that as of that date, the remaining useful life is 5 years. What amount should be reported for patent amortization expense for 2012?
Accounting as a proprietary fund : Which of the following funds of a government uses the same basis of accounting as a proprietary fund?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the transit time of an electron

Consider the 2.0micrometer long GaAs device where the E-field is 5kV/cm and Mn*=.067M0. Calculate the transit time of an electron through the device if the mobility is 8000 cm^2V-s.

  Carrying a uniformy distributed load

The bending moment M at position x m from the end of a simply supported beam of lenght L m carrying a uniformy distributed load of w Kn m-1 is given by

  Create a window in java

Create a window apllication in java

  The desire is to raise the temperature of the ambient air

The desire is to raise the temperature of the ambient air from 60 degree F to 350 degrees F ---- I need to calculate the amount of steam energy in BTU's per minutes and lbs of steam per minute necessary to accomplish the increase in air temperatur..

  Computing the heat transfer rate

Calculating the heat transfer rate and the rate that entropy is produced in a gear box. A gearbox operating under steady state conditions recieves 24 hp along the input shaft and delivers 10hp along the output shaft

  Turbofan engine on a test stand in the maintenance

The explanation provided below, provide the solution to the problem in simple and easy to understand steps. A turbofan engine on a test stand in the maintenance shop is being run at a continuous setting of 22,700 lbs of thrust. The TSFC is 0.5 lbs/..

  How many kilograms each of pearlite and the proeutectoid

How many kilograms each of pearlite and the proeutectoid phase form? Schematically sketch and label the resulting microstructure.

  Explain linear equations and outputs

A project that will cost $750,000 will require payments as certain milestones are met. The initial payment is $50,000. When 30% of the work is complete an additional payment of $200,000 is due. When 70% of the work is complete another payment of $..

  Capabilities of solidworks motion manager

Prepare a power point presentation and a short report relating to the capabilities of Solidworks Motion Manager.

  Increasing volume of balloon problem

A spherical balloon inflated sos that the volume is increasing at the rate of cubic meter/min. At what rate is the diameter increasing when the diameter is 12 m?

  Determine the largest allowable square cross

Determine the largest allowable square cross section of a steel shaft of length 6 m if the maximum shearing stress is not to exceed 135 MPa

  Explain a particular grade of nitinol sma is capable

A particular grade of Nitinol SMA is capable of upto 6% strain recovery and develops an internal restoration stress of upto 300 MN m-2. Estimate the amount of force and distance of travel that could be triggered by warming a rod

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd