Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a function F with 4 bits of input A3,A2,A1,A0 such that the output of F is
1 if the unsigned binary number represented by A3A2A1A0 is a prime (i.e., 2, 3, 5, 7, 11 or 13).
Otherwise, the output of F is 0.
(a) Write the truth table for F.
(b) Implement F using a 16x1 MUX and nothing else.
(c) Implement F using a 8x1 MUX, some AND gates, some OR gates, and some NOT gates.
A 480 V(rms) source supplies 3 parallel loads: load 1: P1 = 25kW and Q1 = 25 kVAr, no power factor given, no Resistance(R1) given load 2: S2 = 15kVA at power factor 0.8 leading,P2 and Q2 not given and no R2 given
A ideal transformer is rated at 4800/480 volt, at 75KVA. it is connected as a step down auto transformer. find the line and load voltages, turns ratio and total apparent, real and reactive power at full load and at 60% rated load at a power factor..
What kind of EMC filter is needed to reduce emissions from aDC motor. The motor is connected in series with a battery. Anycomponents can be used to design the filter.
Explain the difference between a balanced polyphase system and unbalanced polyphase system. What conditions typically cause a polyphase system to become unbalanced
The current through a particular circuit element is given by i(t) = 10sin(200*pi*t) A. Determine the net charge that passes through the element between t=0 and t=10ms. Repeat for the interval t=0 and t=15ms.
plug the following items into a single circuit breaker in your house (120 V): 0.3 hp fish tank pump, a 9000 watt space heater, a 1800 watt hair dryer, a TV using 409 watts. Calculate the minimum rating of the circuit breaker necessary to safely ca..
The power dissipated in the resistor is 62 W when connected to a 10V source. Find the total dissipated power when the same resistor is connected to a 5V source.
Create a MultiSIM schematic of each of your designs. Provide a screenshot. Perform a simulation of each design to demonstrate the filter behavior. Take a screenshot. From your simulation and screenshot in the above step, what is the gain in dB at t..
Assume the output is taken from the capacitor in this RC system with R=200Ohm and C=1µF. Plot the step and impulse response of the system by using the LSIM (you can use TF function before LSIM to calculate your system coefficients) function of MATLAB..
Consider a 4-bit unipolar binary-weighted D/A converter with v(1)= 1 V, V(0) = 0 V, and Rf= 8R. Obtain the analog output voltage for each of the digital inputs from 0000 to 1111
Add an activehigh overflow indicator and the required detection circuitry. Thecircuit should have inputs a7 through a0, inputs b7 through b0, sumoutputs s7 through s0, and output overflow. For all inputs/outputsuse index 7 as the MSB and index 0 a..
A modulating signal consists of two sinusoidal components: 1 kHz and 3 kHz. The transmitter carrier frequency is 80 kHz. If the signal is applied to an ideal DSB transmitter, indicate the output frequencies (in kHz).
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd