A four cylinder four stroke gasoline internal combustion

Assignment Help Mechanical Engineering
Reference no: EM13628165

A four cylinder, four stroke gasoline internal combustion engine has a bore of 9.4 cm and a stroke of 8.6 cm. The clearance volume is 16% of the cylinder volume when at bottom dead center and the crankshaft rotates at 2400 RPM. The cycle can be modeled as an air-standard Otto cycle with a pressure of 1.0 bar and a temperature of 16°C at the beginning of compression. The maximum temperature in the cycle is 2889 K. Based on this model, calculate the net work per cycle, in kJ, and the power developed by the engine in kW using constant specific heats at 1000K.

Reference no: EM13628165

Questions Cloud

If your friend plans to drive at 750 mph and you plan to : you are eating lunch at your favorite cafe and your friend calls and says he wants to meet you. he is calling from a
You conducted a t-test in your capstone research you did : you conducted a t-test in your capstone research. you did not find a statistically significant difference between your
Assume that you are expecting a medium effect size : you wish to conduct an anova one wayomnibus in your capstone project. in order to insure you have enough power to
For a magnetic system the work done by the system is usub : 1. suppose a room is divided into the front one fifth the middle two fifths and the back two fifths. what is the ratio
A four cylinder four stroke gasoline internal combustion : a four cylinder four stroke gasoline internal combustion engine has a bore of 9.4 cm and a stroke of 8.6 cm. the
You conducted a chi-square goodness of fit test in your : you conducted a chi-square goodness of fit test in your asci 691 capstone project. unfortunately you did not get the
Determine the allowable current in a 10 gage 259 mm : determine the allowable current in a 10 gage 2.59 mm diameter copper wire that is insulated with a 1 cm - o.d. layer of
What value of k will give the lowest expected number of : suppose 240 people are being tested for a disease with a 100 accurate test. each individual has a 7 probability of
If a heat pump is used to pump heat from the outside to the : it is found that 10 btus of heat must be supplied to a house in order to maintain its temperature at 70of when the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Materials engineering i need you to write a report about

i need you to write a report about precipitation hardening of aluminum alloys. i will attach the report format which

  A stainless steel bar 10 inch long and 38 inch in diameter

a stainless steel bar 10 inch long and 38 inch in diameter is loaded in tension and experiences an elastic stretch of

  Problem 110degc water is flowing in a 10-mm diameter smooth

problem 110degc water is flowing in a 10-mm diameter smooth tube. the mass flow rate of the water is 0.15 kgs. the

  Examine deflection of an i-beam under a point load

The purpose of this project is to introduce you to the application of FEA by using the ANSYS software to examine the deflection of an I-beam under a point load.

  The air is first expanded isothermically to 500kpa then

a piston-cylinder device contains 0.15kg of air initially at 2 mpa and 350 degrees celsius. the air is first expanded

  Heat transfer occurs until the volume on the inside of the

a piston-cylinder device contains 1 kg of h2o. the water is at 800oc and a pressure of 20 mpa. heat transfer occurs

  If he starts at va 2 fts where s 0 at a determine the

when the motorcyclist is at a he increases his speed along the vertical circular path at the rate of v v dot 0.04s

  Determine the minimum diameter required for the shaft use

a simple torsion-bar spring has the shear stress in the steel g 80gpa shaft is not to exceed 90 mpa and the vertical

  Determine the acceleration of the piston

Knowing that crank AB rotates about point A with a constant angular velocity of 900 rpm clockwise, determine the acceleration of the piston P when θ = 120°.

  Calculate the time rate of change hb of angular momentum

a small 4 oz particle is prokected with a horizontal velocity of 6ftsec into the top of smooth circular guide fixed in

  What are the conditions for valid object representation in

do you think the objects created in the following representation schema are always valid? justify your answers with

  A well-insulated piston-cylinder assembly is connected by a

a well-insulated piston-cylinder assembly is connected by a valve to an air supply line at 8 bar. initially the air

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd