A fluid viscosity10-2 nsm2 density 800 kgm3 flows with a

Assignment Help Mechanical Engineering
Reference no: EM13629196

A fluid (viscosity=10^-2 Ns/m2, density =800 kg/m3) flows with a mean velocity of 4 cm/s in a 10 cm smooth pipe.

a. What is the value of Reynolds number?

b. What is the magnitude of the maximum velocity in the pipe?

c. What is the magnitude of the friction factor?

d. What is the shear stress at the wall?

e. What is the shear stress at a radial distance of 25 mm from the center of the pipe?

Reference no: EM13629196

Questions Cloud

The compressor turbine of a simple gas turbine each have : the compressor turbine of a simple gas turbine each have isentopic efficiencies of 90. the compressor pressure ratio is
If the friction force on the side walls can be neglected : we have a laminar fully developed channel flow of water with density 1000 kgm3 and kinematic viscosity 1.3x10-6 m2s.
Ignoring the heat transfer changes in potential energy and : hot air steadily enters a gas turbine at 5 bar 900 k and exits at 1 bar 600 k and a velocity of 100 ms. the mass flow
Five kilograms of water initially a saturated vapor at 100 : five kilograms of water initially a saturated vapor at 100 kpa is cooled to saturated liquid while the pressure is
A fluid viscosity10-2 nsm2 density 800 kgm3 flows with a : a fluid viscosity10-2 nsm2 density 800 kgm3 flows with a mean velocity of 4 cms in a 10 cm smooth pipe.a. what is the
Assume that womens heights are normally distrubted with a : assume that womens heights are normally distrubted with a mean 62.4 inches and a sd given by 2.6 inch.a. if a woman is
A section of a roller-coaster is a horizontal cylindrical : a section of a roller-coaster is a horizontal cylindrical helix. the velocity of the cars as they pass point a is 15
A girl is standing at the edge of a cliff 111 m above the : a girl is standing at the edge of a cliff 111 m above the ground. she reaches out over the edge of the cliff and throws
Water 15 c flows in a horizontal schedule 40 pipe that has : water 15 c flows in a horizontal schedule 40 pipe that has a nominal diameter of 0.5 in. the reynolds number is re1000.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A design specification requires that a 782 pound vehicle

a design specification requires that a 782 pound vehicle be able to climb a 16 degree incline at 14 mph. what is the

  Determine the new velocity v of the center of the disk as

a unifrom circular disk which rolls with a velocity v without slipping encounters an abrupt change in the direction of

  A frac12 -in-diameter unf sae grade 52 bolt with rolled

a frac12 -in-diameter unf sae grade 5.2 bolt with rolled threads is preloaded to 80 of its proof load when clamping a

  To determine the mass-transfer coefficient of chlorine in

silicon tetrachloride sicl4 is a key chemical in the silicon chemical vapor deposition. it is used in the production of

  Suppose that a nickel filter is required to produce an

1. graphically verify moseleys law for the k beta1 lines of cu mo and w.2. acalculate the mass an linear absorption

  Calculate the vacancy concentration in aluminum at 50 70

1 calculate the density of al in gcm3 given that it forms an fcc crystal structure with an atomic radius of 0.143 nm

  Determine the pressure difference in psi associated with

sometime when riding an elevator or driving up or down a hilly road a persons ears pop as the pressure difference

  Estimate the screw torque erquired to raise the load if

a square-threaded power screw with single thread is used to raise a load of 25000lb. the screw has a mean diameter of 1

  Water at 50kpa and 150 deg celsius enters a constant-area

water at 50kpa and 150 deg celsius enters a constant-area pipe a0.08m2 with a velocity of 11ms. at some point farther

  Determine the peak runoff

Determine the peak runoff from 500 ft of pavement(32ft wide) that drains toward a gutter(for 10 years freq. storm), the pavement slope is .0005, n=.016 and c=.9

  Calculate the work done and the final temperature for the

calculate the work done and the final temperature for the following processespolytropic n 1.0 1.0 kg of air t1 1470

  The outer spring has d 50 mm d 9mm and n 5 the inner

two concentric helical compression springs made of steel and having the same length when loaded and when unloaded are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd