A flag pole made of solid aluminum is 20 feet tall and one

Assignment Help Mechanical Engineering
Reference no: EM13627805

A flag pole made of solid aluminum is 20 feet tall and one inch in diameter. The pole is situated in full sunlight, and the arriving solar energy is 310 watts per square meter of the surface on which the solar photons are incident. The pole is painted black and absorbs 95% of the energy that is incident upon it. The wind is strong so that the heat transfer coefficient h for convection is 20.9 W/m^2-K, and the temperature of the air is 29.2 C. The rate at which the emitted photons carry energy away is given by Energy Rate [W] = 5.4*10^-8*T^4*A where T is temp of the pole in Kelvin and A is the surface area of flag pole which radiation is emitted.

Using the First Law of Thermodynamics you get Q(dot) = 0.

Net rate of heat inflow = 0 = rate at which solar energy is absorbed - rate at which radiant energy leaves - rate at which convection extracts heat

Solar energy is not able to wrap around a pole, but radiant energy is emitted uniformly from the entire surface of the pole. Convection extracts heat from the entire surface of the pole. Be careful to work this problem in Kelvin rather than Celsius.

What is the equilibrium temperature of the flag pole?

Reference no: EM13627805

Questions Cloud

The internal energy of a gas is 1000 j the gas is : the internal energy of a gas is 1000 j. the gas is compressed adiabatically and its volume decreases by 500 cm3. if the
An orifice meter is installed in a 12 foot ductile iron : an orifice meter is installed in a 12 foot ductile iron pipe carrying water at 60 deg f. a mercury manometer is used to
Determine the size of the contact patch the contact : determine the size of the contact patch the contact stresses and the maximum shear stress for a 40 mm diameter steel
Calculate a characteristic reynolds number for an aircraft : calculate a characteristic reynolds number for an aircraft cruising at 1000kmhr. make any assumptions necessary and
A flag pole made of solid aluminum is 20 feet tall and one : a flag pole made of solid aluminum is 20 feet tall and one inch in diameter. the pole is situated in full sunlight and
Suppose you perform a cross between two true-breeding : suppose you perform a cross between two true-breeding stocks of garden peas with respect to two characteristics of
Consider a low speed one-circuit wind tunnel with an inlet : consider a low speed one-circuit wind tunnel with an inlet to throat ratio of 12. the pressure difference between the
The heat flux passing through a plane wall of a : the heat flux passing through a plane wall of a well-insulated house is q 2.5 btuhr-ft2 when the temperature of the
A mass of 040 kg hanging from a spring with a spring : a mass of 0.40 kg hanging from a spring with a spring constant of 80.0 nm is set into an up-and-down simple harmonic

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd