A dragster comes off the start line with an acceleration

Assignment Help Mechanical Engineering
Reference no: EM13701639

A dragster comes off the start line with an acceleration of 4 m/s2. The acceleration increases uniformly from 4 m/s2 to 10m/s2 over 3 seconds, then remains constant to the finish line (500m). Find: a) the acceleration as a function of time (make a graph) b) the velocity as a function of time c) the distance as a function of time d) the time at which it finishes

Reference no: EM13701639

Questions Cloud

Elapse until the rate of filtration drops : A liquid is filtered at pressure of 200 kPa through a 0.2 m2 filter. Initial results indicate that 5 minutes is required to filter 0.3 m3 of liquid. Determine the time that will elapse until the rate of filtration drops to 5 * 10-5 m3 s-1. The filter..
Specific heats of pea soup and can metal are respectively : An autoclave contains 1000 cans of pea soup. It is heated to an overall temperature of 100°C. If the cans are to be cooled to 40°C before leaving the autoclave, how much cooling water is required if it enters at 15°C and leaves at 35°C? The speci..
Maximum heat demand for freezing is twice average demand : It is desired to establish freezing of 10,000 loaves of bread each weighing 0.75 kg from an initial room temperature of 18°C to a final store temperature of -18°C. If this is to be carried out in such a way that the maximum heat demand for the free..
What is the total amount of pitts inventory : At the end of the year, a physical inventory showed it had ending inventory of $140,000. Calculate Reid & Company's cost of goods sold for the year and what is the total amount of Pitts' inventory at year end?
A dragster comes off the start line with an acceleration : A dragster comes off the start line with an acceleration of 4 m/s2. The acceleration increases uniformly from 4 m/s2 to 10m/s2 over 3 seconds, then remains constant to the finish line (500m). Find: a) the acceleration as a function of time (make a gr..
Coefficient of friction between the container and the floor : A 40 kg container is initially at rest and then is pushed by a hydraulic cylinder with a force (kN) = 160 - 10 s. The coefficient of friction between the container and the floor is .26. Give one reason why it may be quickest to use energy methods to ..
Intended target should the supply package be dropped : A pilot wants to drop supplies from an aircraft flying at a horizontal velocity of 300 km/hr at an altitude of 500 m. How far (distance and time) before the intended target should the supply package be dropped?
Determine the total entropy change for this process : A 60-kg iron block and a 39-kg copper block, both initially at 76oC, are dropped into a large lake at 9oC. Thermal equilibrium is established after a while as a result of heat transfer between the blocks and the lake water. Determine the total entrop..
Determine the change of the entropy of the entire system : Ten grams of computer chips with a specific heat of 0.3 kJ/kg dot K are initially at 15 degrees C. These chips are cooled by placement in 5 grams of saturated liquid R134a at -38 degrees C.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd