A disk has a mass of 4kg and a radius of 90mm it is at rest

Assignment Help Mechanical Engineering
Reference no: EM13345105

A disk has a mass of 4kg and a radius of 90mm, it is at rest when it is placed in contact with the belt, which moves with a constat speed (v =15m/s). knowing that friction is .25 between the disk and the belt. Determine the number of revolution by the disk. 

Reference no: EM13345105

Questions Cloud

A piece of gold jewelry that weighs 935 g and has a volume : a piece of gold jewelry that weighs 9.35 g and has a volume of 0.654 cm3. the density of pure gold is 19.3 gcm3 and the
An aqueous solution of a nonelectrolyte boils at 10032c : an aqueous solution of a nonelectrolyte boils at 100.32c. what is its expected freezing
Ethylene glycol hoch2ch2oh is effective as an antifreeze : ethylene glycol hoch2ch2oh is effective as an antifreeze but it also raises the boiling temperature of automobile
A tank is initially filled with 1000 litres of brine : a tank is initially filled with 1000 litres of brine containing 0.15kg of salt per litre. fresh brine containing
A disk has a mass of 4kg and a radius of 90mm it is at rest : a disk has a mass of 4kg and a radius of 90mm it is at rest when it is placed in contact with the belt which moves with
When relatively small amounts of magnesium burn the fires : when relatively small amounts of magnesium burn the fires are extinguished using commercially available dry powder. why
The voltage drops across three resistors in series are : the voltage drops across three resistors in series are measured 10v 15v and 25v. if the largest resistor is 47 ohms
A gas expands and does p-v work on the surroundings equal : a gas expands and does p-v work on the surroundings equal to 343 j. at the same time it absorbs 159 j of heat from the
If the fuel-to-air ratio is 006nbspand the pressure and : a reciprocating engine for light aircraft modeled after the avco lycoming 0.235nbspengine has the following

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd