A diatomic calorically perfect ideal gas in a

Assignment Help Mechanical Engineering
Reference no: EM13629738

A diatomic calorically perfect ideal gas in a piston-cylinder assembly undergoes a cycle: from 1 to 2 is isothermal, from 2 to 3 is polytropic with n=1.4, for 3 to 4 is isothermal, and from 4 to 1 is again a polytropic with n=1.4. If v1= 1 m^3/kg, T1= 1000K, v3= 2 m^3/kg, and T3= 300K, find the specific heat transfer of the cycle.

Reference no: EM13629738

Questions Cloud

The probability is 33 that a message sent over a : the probability is 33 that a message sent over a communication channel is garbled. if the message is sent repeatedly
A spherical hot-air balloon is initially filled with air at : a spherical hot-air balloon is initially filled with air at 120 kpa and 35oc with an initial diameter of 3 m. air
A j type thermocouple referenced at 70f has a measured emf : a j type thermocouple referenced at 70f has a measured emf of 2.878mv. what is the tempature of the measured
The size of fish in a lake follows a normal distribution : the size of fish in a lake follows a normal distribution with mean m 1 lb 4 oz and standard deviation s 3 oz . fish
A diatomic calorically perfect ideal gas in a : a diatomic calorically perfect ideal gas in a piston-cylinder assembly undergoes a cycle from 1 to 2 is isothermal from
A spherical hot-air balloon is initially filled with air at : a spherical hot-air balloon is initially filled with air at 120 kpa and 35oc with an initial diameter of 3 m. air
A certain type of engine suffers a critical failure with : a certain type of engine suffers a critical failure with probability 1.59 each start.a. what is the probability of a
Find how much should be cut off from free length of the : a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf
Then heat is removed to bring the pressure back down to 1 : these problems are in a cycle context. in this cycle air is first compressed in a piston-cylinder cylinder assembly in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Etermine the principal stresses and maximum shearing stress

four forces are applied to a W200x35.9 rolled beam as shown. determine the principal stresses and maximum shearing stress at point a.

  The flow rate 5 kgs determine the direction of flow and

a fluid flows through an adiabatic device. at one end the velocity is 30 ms h 320 kjkg and s 0.695 kjkg k and at the

  Design a garage door controller using plc ladder diagram

Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR)

  This unit cell is similar to the face-centered cubic unit

consider the cuau crystal structure. it can be described as a simple cubic lattice with a basis of cu 0 0 0 cu 1 2 1 2

  Assume the density of this metal at the given temperature

the number of vacancies per cubic meter of a metal at 600degc is 3.11025 vacanciesm3. assume the density of this metal

  A cyclic steam power plant is to be designed for a steam

a cyclic steam power plant is to be designed for a steam temperature at turbine inlet of 360 celsius and an exhaust

  A rectactangular surface is placed in a vertical position

a rectactangular surface is placed in a vertical position in fresh water with its top and bottom edges horizontal. if

  Where must it strike the air water interface relative to

a beam of light is emitted in a pool of water from a depth of 69.7 cm. where must it strike the air water interface

  Asuming the average fuel composition and energy content

u.s. energy use was approximately 100 quads quadrillion btu in 2008. about 85 of this energy was supplied by burning

  Dtermine the moles of co that are produced at the surface

a 20-cm-long cylindrical graphite pure carbon rod is inserted into an oxidizing atmosphere at 1145 k and 1.013105 pa

  The isentropic efficiencies of turbine and compressor are

question1a piston cylinder device contains 25 g of saturated water vapor that is maintained at constant pressure of 300

  Calculate the ratio of the initial to final speed of sound

Air expands isentropically from 1.5 MPa and 60 C (centigrade) to 0.4 Mpa. Calculate the ratio of the initial to final speed of sound.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd