A cylindrical steel pressure vessel with mean diameter

Assignment Help Mechanical Engineering
Reference no: EM13524188

A cylindrical steel pressure vessel with mean diameter 1.5 m, length 4.0 m, wall thickness 8.0 mm and closed ends is subjected to an internal pressure of 1.2 MPa. Find the circumferential and axial strains and hence determine how much the volume inside the vessel increases due to pressurization. (Esteel = 210 GPa, νsteel = 0.30). Assume that the ends remain flat.

Reference no: EM13524188

Questions Cloud

Find what maximum force is required to load the gun : A spring-loaded pellet gun is designed to fire 2.50 g projectiles horizontally at a speed of 50.7 m/s. What maximum force is required to load the gun
Find how much energy did he burn : Rocky's base metabolic rate is 100 W (when not exercising). He weighs 80 kg. This morning, he climbed stairs 25-cm high at the rate of 140 steps per minute for 30 minutes on a Stairmaster. How much energy did he burn (in J and in kWh)
Determine the pressure inside the cylinder : A gas is contained in a vertical, frictionless piston-cylinder device. The piston has a mass of 4 kg and a cross-sectional area of 40 cm2. Determine the pressure inside the cylinder
Find the period of simple harmonic motion for this pendulum : A simple pendulum is 7.00 m long. What is the period of simple harmonic motion for this pendulum if it is located in an elevator accelerating upward at 5.00 m/s2
A cylindrical steel pressure vessel with mean diameter : A cylindrical steel pressure vessel with mean diameter 1.5 m
Find the force on the block at given instant : A 0.49 kg block attached to a spring with force constant 150 N/m is free to move on a frictionless, At that instant, find the force on the block
Explain the cathode ph in co/co2+(1.00 m)//h1+(x m) : What is the cathode pH in Co/Co2+(1.00 M)//H1+(x M), H2(1.0 atm)/Pt if E = 0.01 V? Give the pH to 0.01.
Who are stakeholders and how do they influence regulation : Who are the stakeholders and how do they influence this regulation - What are the key concerns - Organic farmers requires Monsanto company has to follow the food regulation.
Explain the cell potential of the galvanic cell constructed : The standard reduction potentials of the X1+/X and Y3+/Y couples are 0.23 V and -0.28 V, respectively. What is the cell potential (to the nearest 0.01 V) of the galvanic cell constructed from the two couples if [X1+] = 0.213 M and [Y3+] = 0.0100 M

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the truck moves along a circular curve with radius r at

a tank truck carries a cargo of liquid which fills 23 of the tank figure 3. the tank is open tonbspthe atmosphere. if

  Determine the minimum required wire diameter

A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2 and a yield strength of 860 MPa (12..

  A brayton cycle uses air

A Brayton cycle uses air and produces a net work of 14000 Btu/s with an inlet state of 60°F,

  Determine the surface temperatures on the two sides

(a) Determine the surface temperatures on the two sides of the circuit board.

  Find the average velocity of flow at section b

find the average velocity of flow at section B, and the pressure difference between sections A and B.

  What is the acceleration of the truck

What is the acceleration of the truck if the coupling at C suddenly fails? The car wheels are free to roll. Neglect the mass of the wheels.

  Calculate the work done by the gas on the piston

energy is added to a piston cylinder arrangement, and the piston is withdrawn in such a way that the quantity PV remains constant. the initial pressure and volume are 200kpa and 2m3, respectively. the final pressure is 100kpa, calculate the work d..

  Describe the four incorrect assumptions concerning robot

Describe the four incorrect assumptions concerning robot - arm movement that are most frequently responsible for impact accidents.

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  What is the section lift coefficient

Consider a NACA 0009 airfoil that has a plain flap whose length is 0.2c and which is deflected 25. a. Calculate cl and cmc/4 When the geometric angle of attack is 4 degrees, what is the section lift coefficient? Where is the center of pressure?

  Question 1the naca 4412 airfoil has a mean camber line

question 1the naca 4412 airfoil has a mean camber line given byby using thin airfoil theory calculatea. its zero-lift

  Question the two dof system below has two moving masses m1

question the two dof system below has two moving masses m1 m2 with an input force of ft applied to m . the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd