A convenient and secure attachment point for fall

Assignment Help Mechanical Engineering
Reference no: EM13344297

A convenient and secure attachment point for fall protection lines is located 35 feet above ground level on the exterior wall of a building. A 20-foot safety line is available for connection to this attachment point. What is the lowest and highest level at which a work platform can be safely positioned for workers to be protected by the safety line (assume it is attached to the worker's safety harness D-ring). Show work and give a web site 

Reference no: EM13344297

Questions Cloud

A cylindrical bar of radius 15 mm and length 100 mm is held : a cylindrical bar of radius 15 mm and length 100 mm is held at both ends. if at 30 degc no axial force exists in the
If 370 grams of hydrogen sulfide gas h2s mm 3408 gmol : if 37.0 grams of hydrogen sulfide gas h2s mm 34.08 gmol react with 37.1 grams of oxygen gas o2 mm 32.00 gmol what is
Analyze how the reforms of mikhail gorbachev led to the : analyze how the reforms of mikhail gorbachev led to the breakup of the soviet union. point out what events led to the
If 1209 ml of water is shaken with a gas at 0860 atm it : if 120.9 ml of water is shaken with a gas at 0.860 atm it will dissolve 0.00286 g of the gas. estimate the henrys law
A convenient and secure attachment point for fall : a convenient and secure attachment point for fall protection lines is located 35 feet above ground level on the
If 488 g so2 escaped into the atmosphere and all the : if 488 g so2 escaped into the atmosphere and all the escaped so2 were converted to h2so4. how many grams of h2so4 would
A preheater involves the use of condensing steam at 100 on : a preheater involves the use of condensing steam at 100? on the inside of a bank of tubes to heat air that enters at 1
The element boron has two naturally occurring isotopes with : the element boron has two naturally occurring isotopes with masses of 10.0129 amu and 11.0093 amu. what is the percent
The hawkins supply company is currently faced with an : the hawkins supply company is currently faced with an inventory rotation problem.this difficulty stems from the fact

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Etermine the principal stresses and maximum shearing stress

four forces are applied to a W200x35.9 rolled beam as shown. determine the principal stresses and maximum shearing stress at point a.

  What kind of metals are often recommended

What kind of metals are often recommended for use at low temperatures, particularly when any sudden loading of the part is expected?

  How many engagement points on the flywheel

a full revolution has 100 rpm flywheel rotation. the press is equipped with two hand palm buttons mounted on the machine at a distance of 20 inches from the point of operation. How many engagement points on the flywheel would be necessary to make ..

  What is the compression ratio of the cycle

an air-standard otto cycle uses 0.1 kg of air and has a clearance of 17%. THe intake conditions are 98 kPa and 37 C and the energy released during combustion is 1600 KJ/kg. What is the compression ratio of the cycle?

  Determine the magnitude and coordinate direction angles

Determine the magnitude and coordinate direction angles of F3 so that the resultant of the three forces acts along the positively y axis and has a magnitude of 600lb.

  Show the principle stresses on the neutral axis

Show the principle stresses on the neutral axis on a correctly oriented element relative to the axis of the beam.

  Determine the volume of chamber

the entire assembly is placed in an environment whose temperature is 200c. determine the volume of chamber 1 when thermodynamic equillibrium has been estabilished.

  What are the tensions in cables ab and ac

Two tow trucks lift a 660 lb motorcycle out of a ravine following an accident. If the motorcycle is in equilibrium in the position shown, what are the tensions in cables AB and AC?

  Plot contours of u-velocity and v-velocity

The velocity profiles at locations x=0.1, 0.30 and 0.5. Plot contours of u-velocity and v-velocity. How many iterations did it take to get your solution?

  Calculate the mass of mixture produced at the mixing stage

calculate the mass of mixture produced at the mixing stage, the mass jam produced from the kettle and the mass od water evaporated from the kettle.

  Explain volumetric flow rate

Air enters a 0.6 m diameter fan at 16 deg C, 101 kPa, and is discharged at 18 deg C, 105 kPa, with a volumetric flow rate of 0.35 m^3/s.

  Determine the stress in a stay at a given temperature

Determine the stress in a stay at a given temperature. A steel 'stay' of effective length 5m is fitted in between the walls of a ships refrigerated compartment when the temperature is 18 degrees centigrade.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd