A catheter is a specialised needle intended for long-term

Assignment Help Mechanical Engineering
Reference no: EM13627131

A catheter is a specialised needle intended for long-term insertion into a vein in a patient's arm. Engineers are redesigning them to cause less discomfort and damage. An intravenous chemotherapy system is based on a new catheter design. A liquid drug flows to the patient from a plastic bag via through a smooth plastic tube. The liquid drug completely fills the tube at the start of the procedure. The bag is at atmospheric pressure and it is 0.75 m vertically above the catheter. The tube is 2 mm in diameter and 2.0 m long. The average blood pressure in the vein is 6500 Pa gauge. The density of the liquid drug being supplied is 1020.4 kg/m
3 and its dynamic viscosity is 2 x 10-3 Pa.s. Exactly 314 mL of the drug must be supplied. In a laboratory experiment, you measured a fitting head loss for the catheter equivalent to 0.068 m of the liquid drug.

(a) What is the key assumption you must make to do this problem?

(b) How long will it take to supply the required amount of drug?

(c) Show by calculation that the key assumption you made was correct.

Reference no: EM13627131

Questions Cloud

Which statement is true about the scope of systematic : which statement is true about the scope of systematic reviews srs?a. srs should be as broad as possibleb. srs should be
In an integrative research review of an intervention s : in an integrative research review of an intervention s effectiveness which statement is true of an inclusion statement
An asteroid is discovered in a nearly circular orbit around : an asteroid is discovered in a nearly circular orbit around the sun with an orbital radius that is 2.25 times earths.
Explain with clear reference to structural mechanisms and : magneto is seeking to produce a new helmet using a deep drawing process in which a sheet of 3103 aluminum will be
A catheter is a specialised needle intended for long-term : a catheter is a specialised needle intended for long-term insertion into a vein in a patients arm. engineers are
After a package is ejected from the plane how long will it : a relief airplane is delivering a food package to a group of people stranded on a very small island. the island is too
Drinking water at 10oc for an office complex must be : drinking water at 10oc for an office complex must be pumped along a horizontal section of pvc pipe 50 m long at 2 ms.
A how much work does he do during a 143-km race in which : bicyclists in the tour de france do enormous amounts of work during a race. for example the average power per kilogram
An aircraft engine is fitted with a single-sided : an aircraft engine is fitted with a single-sided centrifugal compressor. the aircraft flies with a speed of 230 ms at

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd