Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.A cantilever beam is additionally supported using two tierods. Both rods attach to the end of the beam. One rod comes off at 45 degrees and attaches to the same wall that the beamis solidly fixed to. The other rod comes off at 90 degreesand attaches to the ceiling. Find the force in each of therods. given I, area, and E for the beam. Neglect axial compression, and shear in the beam.
2.The cantilevered beam AB is additionally supported usingtwo tie rods. Determine the force in each of theserods. Neglect axial compression and shear in the beam. For the beam, Ib = 200(106)mm4, and for each tie rod, A = 100mm2. Take E = 200 GPa.
The water treatment capacity in 1995 was 165 ML/day. A survey showed that the average per capita water use rate was 700 L/(person.day). Estimate the community's water requirements in 2010
What are the expressions for the shear, V, and the bending moment, M, within the beam between points C and D in terms of Ay, M1, l, w, and x, the distance to the sectional cut from the beam's left end
For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.
find a chlorine demand occurring in your drinking water distribution system (series of pipes that carry drinking water throughout a city), yet there is no increased chlorine demand in the water going through the treatment plant
Derive the 3-h Snyder unit hydrograph for a 100-km^2 watershed where the main stream is 15 km long and the distance from the watershed outlet to the point on the stream nearest to the centroid of the watershed is 7 km.
Air (an ideal gas) enters an adiabatic nozzle at 3 bar and 38 C and exits at 1 bar and -0.78 C. The process is steady. If the velocity at the inlet is 1 m/s, determine the exit velocity and the ratio of the exit area to the inlet area.
The x-component of a velocity field is ax+b.If the flow is steady, two-dimentional and incompressible; generate an expression for velocity component in the y-direction as a function of x and y.
The distance covered by an aerial photograph is determined by both the focal length of the camera and the tilt of the camera. Although the tilt is usually small, both archaeological and Canadian photographs often use larger tilts.
you are a project manager on site where work for 3k.m. long tunnel has been undertaken. the site is remote and takes
The center of gravity G of the 20-in. club is located 12 in. from the knob. knowing that at the instant, G has a velocity of 4 ft/s upwards and the club has an angular velocity of 30 rad/s counterclockwise
The centres of the piers in a bridge are 8.0m apart. The piers are each 0.8m wide. Water flow under the bridge with an upstream depth and velocity of 4.0m and 4.0m/s respectively. The pier has a drag coefficient Cd = 1.5.
A steady-flow compressor is used to compress helium from 15 psia and 70oF at the inlet to 200 psia and 600oF at the outlet. The outlet area and velocity are 0.01 ft2 and 10 ft/s
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd